Actiontec ScreenBeam Pro Business Edition User Manual - Page 41

Setting up P2P Network Parameters

Get Actiontec ScreenBeam Pro Business Edition PDF manuals and user guides View all Actiontec ScreenBeam Pro Business Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

5.3.19. Setting up P2P Network Parameters When AGO is enabled, you can define network parameters for the peer to peer connection, including P2P Wireless Network Name (SSID), Password, IP address, subnet mask, DHCP IP address range. You should configure these parameters when you use the Managed Meetings function. When source devices connect to the receiver, the receiver will assign IP addresses to these devices. And these IP addresses are defined by the parameters discussed in this section. 1. Go to the Network Settings tab page by clicking the Network Settings tab. 2. Go to the Wireless Interface Settings section, and properly configure the network parameters. P2P Wireless Network Name (SSID) and P2P Wireless Network Password: Reserved. P2P IP Address: It is the IP address of the receiver in a peer to peer connection. This IP address is displayed in the bottom left corner of the Ready to connect screen. It is used to access the local management server when AGO is enabled. Note: The P2P IP Address must not be in the range defined by P2P DHCP IP Start and P2P DHCP IP End. P2P Subnet Mask: It is the subnet mask for the network established in the peer to peer connection. P2P DHCP IP Start and P2P DHCP IP End: These two items define the range of IP addresses assigned to the connected devices. Note: These network parameters works when AGO is enabled. 3. Click the Apply button, and then click OK on the pop-up message box to confirm. 38

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
38
5.3.19.
Setting up P2P Network Parameters
When AGO is enabled, you can define network parameters for the peer to peer connection,
including P2P Wireless Network Name (SSID), Password, IP address, subnet mask, DHCP
IP address range.
You should configure these parameters when you use the Managed Meetings function. When
source devices connect to the receiver, the receiver will assign IP addresses to these devices.
And these IP addresses are defined by the parameters discussed in this section.
1. Go to the
Network Settings
tab page by clicking the
Network Settings
tab.
2. Go to the
Wireless Interface Settings
section, and properly configure the network
parameters.
°
P2P Wireless Network Name (SSID)
and
P2P Wireless Network Password
:
Reserved.
°
P2P IP Address
: It is the IP address of the receiver in a peer to peer connection. This
IP address is displayed in the bottom left corner of the
Ready to connect
screen. It is
used to access the local management server when AGO is enabled.
Note
: The P2P IP Address must not be in the range defined by
P2P DHCP IP Start
and
P2P DHCP IP End
.
°
P2P Subnet Mask
: It is the subnet mask for the network established in the peer to peer
connection.
°
P2P DHCP IP Start
and
P2P DHCP IP End
: These two items define the range of IP
addresses assigned to the connected devices.
Note
: These network parameters works when AGO is enabled.
3. Click the
Apply
button, and then click
OK
on the pop-up message box to confirm.