Ariens Deluxe Track 28 Owners Manual - Page 11

Remote Deflector Control, 017, 018, 020, 022, 023

Get Ariens Deluxe Track 28 PDF manuals and user guides View all Ariens Deluxe Track 28 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

NOTE: After the chute rod has been inserted through the hex hole in the control assembly, placing the unit in the service position (see Service Position on page 23) will ease alignment and installation of the hair pin. 8. Secure the chute rod to the control assembly with the hair pin removed in step 6 using the end hole location as shown in Figure 11. Insert the hairpin with the loop end to the left of the chute rod so the control assembly follows a full range of travel. 1 2 3 1. Chute Control Assembly 2. Hairpin 3. Chute Rod Figure 11 OS7157 9. Connect the chute lock cable to the lock arm by fitting the cable ball end into the slot on the lock arm and then insert the chute lock cable fitting into the bracket on the chute pedestal (Figure 12). 10. Adjust and tighten jam nuts on cable to remove cable slack. Be sure not to pretension lock arm so it retracts from the gear teeth see Discharge Chute Control on page 27. 11. Replace the gear cover removed in step 4. 12. Orient the chute and pedestal to its most vertical position and tighten pedestal hardware to 15 - 31 lbf-ft (20 - 42 N•m). 13. Make sure the discharge chute rotates left and right when you push the discharge chute control lever left and right. NOTE: If chute does not stay in position, adjust as directed in Discharge Chute Control on page 27, or repair before operation. Remote Deflector Control (921013, 017, 018, 020, 022, 023) (Figure 13) Connect the cable end to the cable anchor on the discharge deflector before clipping the cable to the cable bracket on the discharge chute. 1. Route deflector remote cable along the left side of the chute pedestal. 2. Insert the barrel on the cable end into the bracket on left side of chute deflector (Figure 13). 3. Hold seal out of the way while routing the cable through the bracket on the left side of the discharge chute, and then push the cable fitting into the bracket. 4. Push the seal securely over the end of the cable fitting to prevent water from entering the cable. Check deflector travel. Adjust nut on cable end under handlebar to obtain full travel, if necessary (see Remote Deflector Control on page 27). . 2 3 1 3 Figure 12 5 4 OS7271 GB - 11 1. Cable Anchor 2. Cable End 3. Deflector Cable 4. Cable Fitting 5. Cable Bracket Figure 13 OS7070

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
GB - 11
NOTE:
After the chute rod has been inserted
through the hex hole in the control assembly,
placing the unit in the service position (see
Service Position
on page 23) will ease
alignment and installation of the hair pin.
8. Secure the chute rod to the control
assembly with the hair pin removed in
step 6 using the end hole location as
shown in Figure 11. Insert the hairpin
with the loop end to the left of the chute
rod so the control assembly follows a full
range of travel.
9. Connect the chute lock cable to the lock
arm by fitting the cable ball end into the
slot on the lock arm and then insert the
chute lock cable fitting into the bracket
on the chute pedestal (Figure 12).
10. Adjust and tighten jam nuts on cable to
remove cable slack. Be sure not to
pretension lock arm so it retracts from
the gear teeth see
Discharge Chute
Control
on page 27.
11. Replace the gear cover removed in
step 4.
12. Orient the chute and pedestal to its most
vertical position and tighten pedestal
hardware to 15 – 31 lbf-ft (20 – 42 N•m).
13. Make sure the discharge chute rotates
left and right when you push the
discharge chute control lever left and
right.
NOTE:
If chute does not stay in position,
adjust as directed in
Discharge Chute Control
on page 27, or repair before operation.
Remote Deflector Control
(921013, 017, 018, 020, 022, 023)
(Figure 13)
Connect the cable end to the cable anchor on
the discharge deflector before clipping the
cable to the cable bracket on the discharge
chute.
1. Route deflector remote cable along the
left side of the chute pedestal.
2. Insert the barrel on the cable end into
the bracket on left side of chute deflector
(Figure 13).
3. Hold seal out of the way while routing
the cable through the bracket on the left
side of the discharge chute, and then
push the cable fitting into the bracket.
4. Push the seal securely over the end of
the cable fitting to prevent water from
entering the cable.
Check deflector travel. Adjust nut on cable
end under handlebar to obtain full travel, if
necessary
(see
Remote Deflector Control
on
page 27).
.
Figure 11
1.
Chute Control
Assembly
2. Hairpin
3.
Chute Rod
1
2
3
OS7157
Figure 12
OS7271
Figure 13
1.
Cable Anchor
2.
Cable End
3.
Deflector Cable
4.
Cable Fitting
5.
Cable Bracket
1
2
3
5
4
3
OS7070