Asus AP1720-E2 AP1720-E2 English version manual - Page 72

Power suppy modules

Get Asus AP1720-E2 PDF manuals and user guides View all Asus AP1720-E2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

2.10.7 Power suppy modules The barebone server system power supply modules come in three configurations: 600 W single power supply (110 V / 220 V autoswitch) 2 x 300 W dual power supply (110 V / 220 V autoswitch) 3 x 300 W redundant power supply (110 V / 220 V autoswitch) Refer to this section when removing or installing power supply modules to the barebone system. You MUST disconnect all power cable plugs from the motherboard and other installed devices before removing the 600 W single power supply. The picture below shows the motherboard and device connectors where the power plugs are connected. Refer to the Appendix at the end of this document for the power supply specifications. 4 2 3 5 1 6 1 24-pin ATX (motherboard power connector) 2 8-pin +12V (motherboard power connector) 3 2 x 4-pin plugs (SCSI/SATA backplane; hidden) 4 4-pin plug (optical drive) 5 4-pin plug (floppy disk drive; hidden) 6 2 x 4-pin plugs (second SCSI backplane, if available; hidden) 2-52 Chapter 2: Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
Chapter 2:
Hardware setup
2-52
2.10.7
Power suppy modules
The barebone server system power supply modules come in three
configurations:
You MUST disconnect all power cable plugs from the motherboard and
other installed devices before removing the 600 W single power supply.
The picture below shows the motherboard and device connectors where
the power plugs are connected. Refer to the Appendix at the end of this
document for the power supply specifications.
1
24-pin ATX (motherboard power connector)
2
8-pin +12V (motherboard power connector)
3
2 x 4-pin plugs (SCSI/SATA backplane;
hidden
)
4
4-pin plug (optical drive)
5
4-pin plug (floppy disk drive;
hidden
)
6
2 x 4-pin plugs (second SCSI backplane, if available;
hidden
)
1
6
5
2
4
600 W single
power supply
(110 V / 220 V autoswitch)
2 x 300 W dual
power supply
(110 V / 220 V autoswitch)
3 x 300 W redundant
power supply
(110 V / 220 V autoswitch)
3
Refer to this section when removing or installing power supply modules to
the barebone system.