Asus E500-CI CUW-RM User Manual - Page 34

Floppy Disk Drive Connector 34-1 pin FLOPPY

Get Asus E500-CI PDF manuals and user guides View all Asus E500-CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

3. HARDWARE SETUP 9) Primary / Secondary IDE Connectors (40-1 pin PRIMARY/SECONDARY) These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable. Connect the cable's blue connector to the motherboard's primary (recommended) or secondary IDE connector, and then connect the gray connector to your UltraDMA/66 slave device (hard disk drive) and the black connector to your UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices be connected to the secondary IDE connector. If you install two hard disks, you must configure the second drive to Slave mode by setting its jumper accordingly. Refer to your hard disk documentation for the jumper settings. BIOS now supports specific device bootup (see Boot Sequence in 4.6 Boot Menu). (Pin 20 is removed to prevent inserting in the wrong orientation when using ribbon cables with pin 20 plugged). If you have more than two UltraDMA/66 devices, you will need to purchase another UltraDMA/66 cable. NOTE: A small hole near the blue connector on the UltraDMA/66 cable is intentional. TIP: You may configure two hard disks to be both Masters with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector. You may install one operating system on an IDE drive and another on a SCSI drive and select the boot disk through Boot Sequence in 4.6 Boot Menu. IMPORTANT: UltraDMA/66 IDE devices must use an 80 pin IDE cable. Secondary IDE Connector Primary IDE Connector CUW-RM ® NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1 PIN 1 CUW-RM IDE Connectors 10) Floppy Disk Drive Connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting the single end to the board, connect the two plugs on the other end to the floppy drives. (Pin 5 is removed to prevent inserting in the wrong orienta- tion when using ribbon cables with pin 5 plugged). 3. H/W SETUP Connectors CUW-RM ® NOTE: Orient the red markings on the floppy ribbon cable to PIN 1 PIN 1 CUW-RM Floppy Disk Drive Connector 34 ASUS CUW-RM User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
34
ASUS CUW-RM User’s Manual
Connectors
3.
H/W SETUP
3.
HARDWARE SETUP
9)
Primary / Secondary IDE Connectors
(40-1 pin PRIMARY/SECONDARY)
These connectors support the provided UltraDMA/66 IDE hard disk ribbon cable.
Connect the cable’s blue connector to the motherboard’s primary (recommended)
or secondary IDE connector, and then connect the gray connector to your
UltraDMA/66 slave device (hard disk drive) and the black connector to your
UltraDMA/66 master device. It is recommended that non-UltraDMA/66 devices
be connected to the secondary IDE connector. If you install two hard disks, you
must configure the second drive to Slave mode by setting its jumper accord-
ingly. Refer to your hard disk documentation for the jumper settings. BIOS now
supports specific device bootup (see
Boot Sequence
in
4.6 Boot Menu
).
(Pin
20 is removed to prevent inserting in the wrong orientation when using
ribbon cables with pin 20 plugged).
If you have more than two UltraDMA/66
devices, you will need to purchase another UltraDMA/66 cable.
NOTE:
A small hole near the blue connector on the UltraDMA/66 cable is in-
tentional.
TIP:
You may configure two hard disks to be both Masters with two ribbon
cables – one for the primary IDE connector and another for the secondary IDE
connector. You may install one operating system on an IDE drive and another on
a SCSI drive and select the boot disk through
Boot Sequence
in
4.6 Boot Menu
.
IMPORTANT: UltraDMA/66 IDE devices must use an 80 pin IDE cable.
®
CUW-RM
CUW-RM IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to
PIN 1
Secondary IDE Connector
Primary IDE Connector
PIN 1
10) Floppy Disk Drive Connector (34-1 pin FLOPPY)
This connector supports the provided floppy drive ribbon cable. After connect-
ing the single end to the board, connect the two plugs on the other end to the
floppy drives.
(Pin 5 is removed to prevent inserting in the wrong orienta-
tion when using ribbon cables with pin 5 plugged).
NOTE:
Orient the red markings on
the floppy ribbon cable to
PIN 1
CUW-RM Floppy Disk Drive Connector
PIN 1
®
CUW-RM