Asus P I-P55T2P4S User Manual - Page 49

IDE HDD Auto Detection

Page 49 highlights

IV. BIOS SOFTWARE IDE HDD Auto Detection This "IDE HDD Auto Detection" option detects the parameters of an IDE hard disk drive, and automatically enters them into the Standard CMOS Setup screen. ROM PCI/ISA BIOS(PI55T2P4) CMOS SETUP UTILITY AWARD SOFTWARE,INC. HARD DISKS TYPE Primary Master : SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE Select Primary Master Option (N=Skip) : N OPTIONS SIZE CYLS HEAD PRECOMP LANDZ SECTOR MODE 2(Y) 1 3 849 823 32 849 1647 16 849 823 32 0 1646 65535 1646 65535 1646 63 LBA 63 NORMAL 63 LARGE Note: Some OSes (like SCO-UNIX) must use "NORMAL" for installation ESC : Skip Up to four IDE drives can be detected, with parameters for each listed inside the box. To accept the optimal entries, press the key or else select from the numbers displayed under the OPTIONS field (2, 1, 3 in this case); to skip to the next drive, press the key. If you accept the values, the parameters will appear listed beside the drive letter on the screen. The process then proceeds to the next drive letter. Pressing the key to skip rather than to accept a set of parameters causes the program to enter zeros after that drive letter. Remember that if you are using another IDE controller that does not feature Enhanced IDE support for four devices, you can only install two IDE hard disk drives. Your IDE controller must support the Enhanced IDE features in order to use Drive E and Drive F. The on-board PCI IDE controller supports Enhanced IDE, with two connectors for connecting up to four IDE devices. If you want to use another controller that supports four drives, you must disable the on-board IDE controller in the Chipset Features Setup screen. When auto-detection is completed, the program automatically enters all entries you accepted on the field for that drive in the Standard CMOS Setup screen. Skipped entries are ignored and are not entered in the screen. If you are auto-detecting a hard disk that supports the LBA mode, three lines will appear in the parameter box. Choose the line that lists LBA for an LBA drive. Do not select Large or Normal. IV. BIOS (HardDriveDetect) P/I-P55T2P4 User's Manual 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

P/I-P55T2P4 User's Manual
43
IV.
BIOS SOFTWARE
IV.
BIOS
(Hard Drive Detect)
IDE HDD Auto Detection
This “IDE HDD Auto Detection” option detects the parameters of an IDE
hard disk drive, and automatically enters them into the Standard CMOS
Setup screen.
Up to four IDE drives can be detected, with parameters for each listed in-
side the box.
To accept the optimal entries, press the <Y> key or else select
from the numbers displayed under the OPTIONS field (2, 1, 3 in this case);
to skip to the next drive, press the <N> key.
If you accept the values, the
parameters will appear listed beside the drive letter on the screen.
The pro-
cess then proceeds to the next drive letter.
Pressing the <N> key to skip
rather than to accept a set of parameters causes the program to enter zeros
after that drive letter.
Remember that if you are using another IDE controller that does not feature
Enhanced IDE support for four devices, you can only install two IDE hard
disk drives.
Your IDE controller must support the Enhanced IDE features
in order to use Drive E and Drive F.
The on-board PCI IDE controller
supports Enhanced IDE, with two connectors for connecting up to four IDE
devices.
If you want to use another controller that supports four drives, you
must disable the on-board IDE controller in the Chipset Features Setup
screen.
When auto-detection is completed, the program automatically enters all en-
tries you accepted on the field for that drive in the Standard CMOS Setup
screen.
Skipped entries are ignored and are not entered in the screen.
If you are auto-detecting a hard disk that supports the LBA mode, three
lines will appear in the parameter box.
Choose the line that lists LBA for an
LBA drive.
Do not select Large or Normal.
ROM PCI/ISA BIOS(PI55T2P4)
CMOS SETUP UTILITY
AWARD SOFTWARE,INC.
HARD DISKS
TYPE
SIZE
CYLS
HEAD
PRECOMP
LANDZ
SECTOR
MODE
Primary Master
:
Select Primary Master Option (N=Skip) : N
OPTIONS
SIZE
CYLS
HEAD
PRECOMP
LANDZ
SECTOR
MODE
2(Y)
849
823
32
0
1646
63
LBA
1
849
1647
16
65535
1646
63
NORMAL
3
849
823
32
65535
1646
63
LARGE
Note:
Some OSes (like SCO-UNIX) must use "NORMAL" for installation
ESC : Skip