Asus P4T-F User Manual - Page 24

Installing Memory - p4t memory

Get Asus P4T-F PDF manuals and user guides View all Asus P4T-F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

3. HARDWARE SETUP 3.5.1 Installing Memory The memory module (RIMM) will fit in only one orientation. IMPORTANT: Do not touch the memory module's connectors. Handle the module only by the edges. RIMM Sockets P4T-F RIMM with Heat Spreader P4T-F 184-Pin RIMM Sockets C-RIMM 1. Make sure that the notch keys in the module are aligned with the small ribs inside the RIMM sockets. MOUNTING NOTCH RDRAM (with heat spreader) NOTCH KEYS CONNECTORS 3. H/W SETUP System Memory EJECTOR RIBS (inside socket) (TOP VIEW) 2. With the ejectors in the open position (as shown), push down gently but firmly on the memory module until it snaps into place. The guides on the socket's ejectors should go through the two mounting notches on the module and the ejectors should close. If necessary, push the ejectors inward to secure the mod- ule in place. Removing Memory To release a memory module, push both ejectors outward and pull the module straight up and out of the RIMM sockets. WARNING! RIMM modules become extremely hot during operation. To reduce the risk of personal injury from hot surfaces, allow the modules to cool off before removing them. 24 ASUS P4T-F User's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
24
ASUS P4T-F User’s Manual
3. HARDWARE SETUP
3.5.1
Installing Memory
The memory module (RIMM) will fit in only one orientation.
IMPORTANT:
Do not touch the memory module’s connectors. Handle the mod-
ule only by the edges.
1.
Make sure that the notch keys in the module are aligned with the small ribs
inside the RIMM sockets.
2.
With the ejectors in the open position (as shown), push down gently but firmly
on the memory module until it snaps into place. The guides on the socket’s
ejectors should go through the two mounting notches on the module and the
ejectors should close. If necessary, push the ejectors inward to secure the mod-
ule in place.
Removing Memory
To release a memory module, push both ejectors outward and pull the module straight
up and out of the RIMM sockets.
WARNING!
RIMM modules become extremely hot during operation. To re-
duce the risk of personal injury from hot surfaces, allow the modules to cool off
before removing them.
P4T-F
P4T-F 184-Pin RIMM Sockets
RIMM Sockets
RIMM with Heat Spreader
C-RIMM
System Memory
3. H/W SETUP
NOTCH KEYS
CONNECTORS
RDRAM (with heat spreader)
MOUNTING NOTCH
RIBS (inside socket)
EJECTOR
(TOP VIEW)