Asus RS161-E2 User Manual - Page 28

Hard disk drives

Get Asus RS161-E2 - 0 MB RAM PDF manuals and user guides
UPC - 610839630424
View all Asus RS161-E2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

2.5 Hard disk drives The system supports two hot-swap Serial ATA hard disk drives. To install a hot-swap SATA HDD: 1. Release a drive tray by pushing the spring lock to the right, then pulling the tray lever outward. The drive tray ejects slightly after you pull out the lever. 2. Firmly hold the tray lever and pull the drive tray out of the bay. 3. Take note of the drive tray holes. Each side has three holes to fit different types of hard disk drives. Use two screws on each side to secure the hard disk drive. 4. Place a SATA hard disk drive on the tray, then secure it with four screws. 2-12 Chapter 2: Hardware setup

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
Chapter 2:
Hardware setup
Chapter 2:
Hardware setup
Chapter 2:
Hardware setup
Chapter 2:
Hardware setup
Chapter 2:
Hardware setup
2-12
2-12
2-12
2-12
2-12
2.5
Hard disk drives
The system supports two hot-swap Serial ATA hard disk drives.
To install a hot-swap SATA HDD:
1.
Release a drive tray by
pushing the spring lock to the
right, then pulling the tray
lever outward. The drive tray
ejects slightly after you pull
out the lever.
2.
Firmly hold the tray lever and
pull the drive tray out of the
bay.
3.
Take note of the drive tray
holes. Each side has three holes
to fit different types of hard
disk drives. Use two screws on
each side to secure the hard
disk drive.
4.
Place a SATA hard disk drive on
the tray, then secure it with
four screws.