Axis Communications P1224-E P1214-E Network Camera - User Manual - Page 37

Storage

Get Axis Communications P1224-E PDF manuals and user guides View all Axis Communications P1224-E manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

AXIS P1214-E Network Camera System Options RTP/H.264 The RTP port range and multicast settings are configured under System Options > Network > RTP. The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used. Select Always Multicast Video to start multicast streaming without opening an RTSP session. Bonjour The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol. Bonjour can be disabled under System Options > Network > Bonjour. Storage SD Card NOTICE To prevent corruption of recordings, the SD card should always be unmounted before it is ejected. Note For SD card recommendations see www.axis.com Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with speed class 10. The following SD card file systems are supported: • ext4 - recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access data stored on the card from the Windows operating system, a third-party ext4 driver or application is required. • vFAT - supported by most operating systems for personal computers. The SD card is managed on the System Options > Storage page. Click SD Card to open Storage Management. If the card's status shows as failed, click Check disk to see if the problem can be found and then try Repair. This option is only available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card. To avoid filling the card, it is recommended to remove recordings continuously. Under General Settings, select Remove recordings older than and select the number of days or weeks. To stop writing to the card and protect recordings from being removed, select Lock under General Settings. Network Share Network share allows you to add network storage such as a NAS (network-attached storage). The NAS shall be dedicated for recordings and data from the Axis products connected to the network. For information about reference NAS devices, go to www.axis.com/products/cam_companion_software/supported.htm Note For NAS recommendations see www.axis.com To add a network share: 1. Go to System Options > Storage. 2. Click Network Share. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
AXISP1214–ENetworkCamera
SystemOptions
RTP/H.264
The RTP port range and multicast settings are configured under
SystemOptions>Network>RTP
.
The RTP port range defines the range of ports from which the video ports are automatically selected. For multicast streams, only
certain IP addresses and port numbers should be used.
Select
AlwaysMulticastVideo
to start multicast streaming without opening an RTSP session.
Bonjour
The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating
systems and clients that support this protocol.
Bonjour can be disabled under
SystemOptions>Network>Bonjour
.
Storage
SD Card
NO
NO
NOTICE
TICE
TICE
To prevent corruption of recordings, the SD card should always be unmounted before it is ejected.
Note
For SD card recommendations see
www.axis.com
Supports microSD cards with up to 64 GB of storage. For best recording performance, use a microSDHC or microSDXC card with
speed class 10.
The following SD card file systems are supported:
•
ext4
— recommended due to its resilience against data loss if the card is ejected or if there is abrupt power loss. To access
data stored on the card from the Windows operating system, a third-party ext4 driver or application is required.
•
vFAT
— supported by most operating systems for personal computers.
The SD card is managed on the
SystemOptions>Storage
page. Click
SDCard
to open
StorageManagement
.
If the card’s status shows as failed, click
Checkdisk
to see if the problem can be found and then try
Repair
. This option is only
available for SD cards with ext4. For SD cards with vFAT, use a card reader or computer to troubleshoot the card.
To avoid filling the card, it is recommended to remove recordings continuously. Under
GeneralSettings
, select
Removerecordings
olderthan
and select the number of days or weeks.
To stop writing to the card and protect recordings from being removed, select
Lock
under
GeneralSettings
.
Network Share
Network share allows you to add network storage such as a NAS (network-attached storage). The NAS shall be dedicated for
recordings and data from the Axis products connected to the network. For information about reference NAS devices, go to
www.axis.com/products/cam_companion_software/supported.htm
Note
For NAS recommendations see
www.axis.com
To add a network share:
1. Go to
SystemOptions>Storage
.
2. Click
NetworkShare
.
37