Belkin F5D7230-4_V3000 User Manual - Page 69

Setting Up a Bridge Between your Wireless Router and a, Secondary Access Point

Get Belkin F5D7230-4_V3000 PDF manuals and user guides View all Belkin F5D7230-4_V3000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

section Using the Web-Based Advanced User Interface 1 Setting Up a Bridge Between your Wireless Router and a Secondary Access Point 2 Bridging your Belkin Router to a secondary Access Point requires that you access the Router's Advanced Setup Utility and enter the MAC address of the Access Point in the appropriate area. There are also a 3 few other requirements. PLEASE BE SURE TO FOLLOW THE STEPS BELOW, CAREFULLY. 4 1. Set your Access Point to the same channel as the Router. By default, the Router and Access Point channels are set to channel 11 at the factory. If you have never changed the channel, you 5 don't need to do anything (for more information on changing channels, see page 47 of this manual). 6 2. Find the Access Point's MAC address on the bottom of the Access Point. There are two MAC addresses on the bottom label. You will need the MAC address named "WLAN MAC Address". 7 The MAC address starts with 0030BD and is followed by six other numbers or letters (i.e. 0030BD-XXXXXX). Write the MAC address 8 below. Go to the next step. Serial # F5D7131 FCC ID: K7SF5D7130A Complies with Canada RSS-210 IC: 3623A-F5D7130A WLAN MAC Address Wireless Range Extender/ Access Point model # F5D7131 0030BD-XXXXXX LAN MAC Address 9 10 P81807 11 3. Place your secondary Access Point within range of your Wireless Router and near the area where you want to extend the range or add the network segment. Typically, indoor range should be between 100 and 200 feet. 4. Connect power to your Access Point. Make sure the Access Point is on and proceed to the next step. 67

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
Using the Web-Based Advanced User Interface
67
section
2
1
3
4
5
6
7
8
9
10
11
Setting Up a Bridge Between your Wireless Router and a
Secondary Access Point
Bridging your Belkin Router to a secondary Access Point requires that
you access the Router’s Advanced Setup Utility and enter the MAC
address of the Access Point in the appropriate area. There are also a
few other requirements.
PLEASE BE SURE TO FOLLOW THE STEPS BELOW,
CAREFULLY.
1.
Set your Access Point to the same channel as the Router. By
default, the Router and Access Point channels are set to channel
11 at the factory. If you have never changed the channel, you
don’t need to do anything (for more information on changing
channels, see page 47 of this manual).
2.
Find the Access Point’s MAC address on the bottom of the
Access Point. There are two MAC addresses on the bottom label.
You will need the MAC address named “WLAN MAC Address”.
The MAC address starts with 0030BD and is followed by six other
numbers or letters (i.e. 0030BD-XXXXXX). Write the MAC address
below. Go to the next step.
3.
Place your secondary Access Point within range of your Wireless
Router and near the area where you want to extend the range
or add the network segment. Typically, indoor range should be
between 100 and 200 feet.
4.
Connect power to your Access Point. Make sure the Access Point
is on and proceed to the next step.
FCC ID: K7SF5D7130A
model
# F5D7131
Wireless
Range Extender/
Access Point
IC: 3623A-F5D7130A
Complies with Canada RSS-210
P81807
F5D7131
WLAN MAC Address
Serial #
LAN MAC Address
0030BD-XXXXXX