Beretta Stampede Old West Beretta Stampede User Manual - Page 35

WARNING, Fig. 7, Fig. 3-A, Fig. 12, CAUTION

Get Beretta Stampede Old West PDF manuals and user guides View all Beretta Stampede Old West manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

! ! ! ! ! 35 WARNING: Be certain the revolver is pointed in a SAFE direction and your other hand is away from the muzzle. WARNING: Do not place your finger on the trigger or inside the trigger guard. 1. With the firearm pointed in a SAFE direction and your finger OFF the trigger, pull the hammer rearward to the half-cock position, allowing the cylinder to rotate. (Fig. 7) 2. Open the loading gate, (Fig. 11) exposing the chamber/cartridge case. 3. Align a chamber/cartridge case to the loading gate. 4. While keeping the gun pointed in a SAFE direction, locate the ejector rod handle on the left side of the gun, below the front of the barrel. (Fig. 3-A) WARNING: Be certain the revolver is pointed in a SAFE direction and your other hand is away from the muzzle. 5. While keeping the gun pointed in a SAFE direction, move the ejector handle fully rearward to push the cartridge or fired cartridge case out of the chamber (Fig. 12). WARNING: If you are ejecting unfired cartridges, use extreme care to be sure they are ejected onto an appropriate surface. Never attempt to catch cartridges or fired cartridge cases as they fall. WARNING: Never allow anything to come in contact with the primer of unfired ammunition. Doing so could cause the ammunition to explode. 6. Operate the ejector rod in each chamber to its full travel to ensure each cartridge or fired cartridge case is fully ejected. CAUTION: Do not to release the ejector rod at its rearward position, allowing it to snap back under spring pressure. Doing so could damage the ejector rod.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
35
WARNING:
Be certain the revolver is pointed in a SAFE direction
and your other hand is away from the muzzle.
WARNING:
Do not place your finger on the trigger or inside the
trigger guard.
1. With the firearm pointed in a SAFE direction and your finger
OFF the trigger, pull the hammer rearward to the half-cock
position, allowing the cylinder to rotate.
(Fig. 7)
2. Open
the
loading
gate,
(Fig.
11)
exposing
the
chamber/cartridge case.
3. Align a chamber/cartridge case to the loading gate.
4. While keeping the gun pointed in a SAFE direction, locate the
ejector rod handle on the left side of the gun, below the front
of the barrel.
(Fig. 3-A)
WARNING:
Be certain the revolver is pointed in a SAFE direction
and your other hand is away from the muzzle.
5. While keeping the gun pointed in a SAFE direction, move the
ejector handle fully rearward to push the cartridge or fired
cartridge case out of the chamber
(Fig. 12)
.
WARNING:
If you are ejecting unfired cartridges, use extreme
care to be sure they are ejected onto an appropriate surface.
Never attempt to catch cartridges or fired cartridge cases as
they fall.
WARNING:
Never allow anything to come in contact with the
primer of unfired ammunition.
Doing so could cause the
ammunition to explode.
6. Operate the ejector rod in each chamber to its full travel to
ensure each cartridge or fired cartridge case is fully ejected.
CAUTION:
Do not to release the ejector rod at its rearward
position, allowing it to snap back under spring pressure.
Doing
so could damage the ejector rod.
!
!
!
!
!