Home » Brother International Manuals » Sewing Machines » Brother International KE-436C » Manual Viewer

Brother International KE-436C Instruction Manual - English - Page 21

Installing the spool stand, If the machine is used without these devices attached

Get Brother International KE-436C PDF manuals and user guides

View all Brother International KE-436C manuals

Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

3. INSTALLATION 3-18. Installing the spool stand Assemble the spool stand (1) while referring to the spool stand instruction manual, and then install the spool stand (1) at the right side of the work table. 2509Q 3-19. Installing the eye guard CAUTION Attach all safety devices before using the sewing machine. If the machine is used without these devices attached, injury may result. Install the eye guard assy (1) to the face plate with the two screws (2). 2684Q 15 KE-436C

Section	Page
front	1
SAFETY INSTRUCTIONS	2
2. Notes on safety	3
3. Warning labels	5
CONTENTS	6
1. NAME OF EACH PART	7
2. SPECIFICATIONS	8
2-1. Specifications	8
3. INSTALLATION	9
3-1. Power table	9
3-2. Installing the control box	10
3-3. Installing the rubber cushions	11
3-4. Installing the oil pan	11
3-5. Installing the cushions	11
3-6. Installing the switching plate	12
3-7. Installing the machine head	12
3-8. Installing the head rest	13
3-9. Installing the liquid cooling tank, optional	13
3-10. Installing the operation panel	13
3-11. Installing the programmer (option)	14
3-12. Connecting the ground wire	14
3-13. Connecting the cords	15
3-14. Piping	17
3-15. Installing the belt cover	19
3-16. Installing the foot switch	19
3-17. Installing the needle sub plate	20
3-18. Installing the spool stand	21
3-19. Installing the eye guard	21
4. LUBRICATION	22
4-1. Lubrication points	22
5. USING THE OPERATION PANEL	23
5-1. Explanation of panel	23
5-2. Using the floppy disk	25
5-3. Using the program R/W (Read/Write) switch	27
5-4. Operating the foot switch	28
5-5. Using the TEST switch (Checking the sewing pattern)	28
5-6. Using the emergency stop switch	29
5-7. Using the thread wiper switch	29
5-8. Adjusting the sewing SPEED control	30
5-9. Changing the X-SCALE and Y-SCALE settings	30
5-10. Using the bobbin thread counter	31
5-11. Using production counter	32
5-12. Using single split mode	33
5-13. Shifting a stitch pattern	34
6. CORRECT USE	35
6-1. Selecting the needle and thread	35
6-2. Installing the needle	35
6-3. Threading the upper thread	35
6-4. Winding the lower thread	36
6-5. Replacing the bobbin case and threading the thread	37
6-6. Thread tension	37
7. SEWING	40
7-1. Before starting sewing....	40
7-2. Sewing operation	40
8. MAINTENANCE AND INSPECTION	42
8-1. Checking the needle	42
8-2. Cleaning the rotary hook	42
8-3. Lubrication	43
8-4. Draining the oil	44
8-5. Cleaning the control box air inlet port	44
8-6. Cleaning the air holes of belt cover and frame side cover	44
8-7. Cleaning the eye guard	44
9. STANDARD ADJUSTMENTS	45
9-1. Adjusting the needle bar height	45
9-2. Adjusting the needle bar lift amount	45
9-3. Adjusting the driver needle guard	46
9-4. Adjusting the needle clearance	46
9-5. Adjusting the shuttle race thread guide	46
9-6. Adjusting the thread take-up amount	47
9-7. Adjusting the movable knife	48
9-8. Adjusting the work clamp lift amount	50
9-9. Work clamp adjustment	51
9-10. Changing the work clamp lift	51
9-11. Work clamp interchangeability	52
9-12. Adjusting the needle up stop position	52
9-13. Adjusting the thread wiper	53
9-14. Adjustment of air pressure	53
9-15. Checking the input sensor and DIP switch input	54
9-16. Checking the input voltage	55
9-17. Clearing all memory settings	55
10. DIP SWITCH	56
10-1. Panel DIP switch functions	56
10-2. DIP switches inside the control box	57
11. CHANGING SPECIAL FUNCTIONS USING THE MEMORY SWITCHES	58
12. SETTING THE WORK CLAMP MODE	62
12-1. Light work clamp	63
13. TABLE OF ERROR CODES	64
14. GAUGE PARTS LIST ACCORDING TO SUBCLASSES	66
15. TROUBLESHOOTING	69
16. OPTIONAL PARTS	72