Brother International KE-436C Instruction Manual - English - Page 62

SETTING THE WORK CLAMP MODE, When memo-3b = 0 initial value

Page 62 highlights

12. SETTING THE WORK CLAMP MODE 12. SETTING THE WORK CLAMP MODE Through the combination of DIP switches A-1 and A-2 on the operation panel, presser motions can be set as follows: When memo-3b = 0 (initial value) DIPA-1 − ON − DIPA-2 − − ON Pedal specifications Two pedals Two pedals Single pedal Raising the presser at the sewing end Presser is raised automatically, then it is lowered by pressing the pedal. (factory default settings) Presser is kept lifted while the presser pedal is pressed. Presser is raised automatically. ON ON Single pedal Presser is raised by pressing the pedal. Special memo-3b settings for pneumatic specifications memo-3b 5 Pedal specifications Two pedals Raising the presser at the sewing end Left presser drops when presser pedal is at the 1st step, and right presser drops when presser pedal is at the 2nd step. Raising is carried out in the reverse order. * Setting used when using the light work clamp function (Refer to "12-1. Light work clamp".) Right presser drops when presser pedal is at the 1st step, and left presser drops 6 Two pedals when presser pedal is at the 2nd step. Raising is carried out in the reverse order. The left/right operating sequence changes alternately for each item sewn when 7 Two pedals using two-pedal operation. Starts with right → left. The left pedal is used to raise and lower the left presser, and the right (center) pedal is used to raise and lower the right presser. 8 Three pedals (Option) The start (right) pedal is used to start sewing. Furthermore, when DIP switch A-2 is at ON, and if one presser is already lowered, pressing the start pedal causes the other presser to be lowered and then sewing starts. When the presser pedal is depressed to the 1st step, both left and right pressers are 9 Two pedals raised simultaneously. When it is pressed to the 2nd step, sewing starts. When the start pedal is depressed, both left and right pressers are lowered 10 Two pedals simultaneously. When the start pedal is released, sewing starts. The left pedal raises and lowers the left and right work clamps, and the right pedal 11 Three pedals (Option) (center) detects the home position. The start (right) pedal is used to start sewing. Furthermore, both work clamps are lowered when DIP switch A-2 is ON, and the stepping foot is also lowered at the same time. The left pedal raises and lowers the left work clamp, and the right pedal (center) detects the home position. 12 Three pedals (Option) When the start pedal (right side) is depressed for a short time (200 ms), the right work clamp is lowered, and when it is depressed for a longer time the right work clamp is lowered and then sewing starts. Furthermore, the right work clamp is lowered when DIP switch A-2 is ON, and the stepping foot is also lowered at the same time. 13 Two pedals Two-pedal operation raises and lowers the left and right work clamps simultaneously, and the stepping foot is lowered at the sewing start. When memo-3b has been used to make a special setting, DIP switches A-1 and A-2 function as follows. • When DIP switch A-1 is at ON, the pressers are not raised automatically at the sewing end. • DIP switch A-2 is ignored except when memo-3b = 8, 11, 12. KE-436C 56

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73

12. SETTING THE WORK CLAMP MODE
56
KE-436C
12. SETTING THE WORK CLAMP MODE
Through the combination of DIP switches A-1 and A-2 on the operation panel, presser motions can be set as follows:
When memo-3b = 0 (initial value)
DIPA-1
DIPA-2
Pedal specifications
Raising the presser at the sewing end
Two pedals
Presser is raised automatically, then it is lowered by pressing the
pedal. (factory default settings)
ON
Two pedals
Presser is kept lifted while the presser pedal is pressed.
ON
Single pedal
Presser is raised automatically.
ON
ON
Single pedal
Presser is raised by pressing the pedal.
Special memo-3b settings for pneumatic specifications
memo-3b
Pedal specifications
Raising the presser at the sewing end
5
Two pedals
Left presser drops when presser pedal is at the 1st step, and right presser drops
when presser pedal is at the 2nd step.
Raising is carried out in the reverse order.
* Setting used when using the light work clamp function (Refer to “12-1. Light work
clamp”.)
6
Two pedals
Right presser drops when presser pedal is at the 1st step, and left presser drops
when presser pedal is at the 2nd step.
Raising is carried out in the reverse order.
7
Two pedals
The left/right operating sequence changes alternately for each item sewn when
using two-pedal operation.
Starts with right
left.
8
Three pedals
(Option)
The left pedal is used to raise and lower the left presser, and the right (center) pedal
is used to raise and lower the right presser.
The start (right) pedal is used to start sewing.
Furthermore, when DIP switch A-2 is at ON, and if one presser is already lowered,
pressing the start pedal causes the other presser to be lowered and then sewing
starts.
9
Two pedals
When the presser pedal is depressed to the 1st step, both left and right pressers are
raised simultaneously.
When it is pressed to the 2nd step, sewing starts.
10
Two pedals
When the start pedal is depressed, both left and right pressers are lowered
simultaneously.
When the start pedal is released, sewing starts.
11
Three pedals
(Option)
The left pedal raises and lowers the left and right work clamps, and the right pedal
(center) detects the home position.
The start (right) pedal is used to start sewing.
Furthermore, both work clamps are lowered when DIP switch A-2 is ON, and the
stepping foot is also lowered at the same time.
12
Three pedals
(Option)
The left pedal raises and lowers the left work clamp, and the right pedal (center)
detects the home position.
When the start pedal (right side) is depressed for a short time (200 ms), the right
work clamp is lowered, and when it is depressed for a longer time the right work
clamp is lowered and then sewing starts.
Furthermore, the right work clamp is lowered when DIP switch A-2 is ON, and the
stepping foot is also lowered at the same time.
13
Two pedals
Two-pedal operation raises and lowers the left and right work clamps
simultaneously, and the stepping foot is lowered at the sewing start.
When memo-3b has been used to make a special setting, DIP switches A-1 and A-2 function as follows.
When DIP switch A-1 is at ON, the pressers are not raised automatically at the sewing end.
DIP switch A-2 is ignored except when memo-3b = 8, 11, 12.