Brother International QL-1100 Users Guide - Page 14

Place the DK Roll into the Roll Spool Guide 1., Thread the DK Roll through the Label Printer.

Get Brother International QL-1100 PDF manuals and user guides View all Brother International QL-1100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Set Up the Label Printer c Place the DK Roll into the Roll Spool Guide (1). • Make sure that the Roll Spool Arm (2) is inserted firmly in the Roll Spool Guide. • Make sure the Stabilizer (3) slides into the notch of the Label Printer. 1 3 2 1 d Thread the DK Roll through the Label Printer. • Align the edge of the DK Roll with the upright edge of the Label Output Slot. • Check that the DK Roll is threaded straight so that the labels will not be skewed. • Push the first label through the Label Output Slot until the end comes out of the Slot as shown. Note If you have difficulty inserting the first label, try inserting from the side under the sensor (1). 1 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
Set Up the Label Printer
6
1
c
Place the DK Roll into the Roll Spool Guide (1).
•
Make sure that the Roll Spool Arm (2) is inserted firmly in the Roll Spool Guide.
•
Make sure the Stabilizer (3) slides into the notch of the Label Printer.
d
Thread the DK Roll through the Label Printer.
•
Align the edge of the DK Roll with the upright edge of the Label Output Slot.
•
Check that the DK Roll is threaded straight so that the labels will not be skewed.
•
Push the first label through the Label Output Slot until the end comes out of the Slot as shown.
Note
If you have difficulty inserting the first label, try inserting from the side under the sensor (1).
1
3
2
1