Brother International SE625 Operation Manual - Page 17

bobbin winder seat, the thread may become

Get Brother International SE625 PDF manuals and user guides View all Brother International SE625 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Winding/Installing the Bobbin Pass the thread under the hook on the bobbin winding e thread guide, and then wind it counterclockwise under the pretension disk. 1 2 3 1 Bobbin winding thread guide 2 Pretension disk 3 Pull it in as far as possible Note • Make sure that the thread is passed under the pretension disk. Wind the thread clockwise around the bobbin 5 or 6 f times, pass the thread through the guide slit in the bobbin winder seat, and then pull the thread to cut it. a Turn on the machine. h Press the "Start/Stop" button once to start winding the i bobbin. When the foot controller is plugged in, press down on the foot controller. 1 GETTING READY Note • When winding transparent nylon thread on the bobbin, stop bobbin winding when the bobbin is 1/2 to 2/3 full. If the bobbin was fully wound with transparent nylon thread, it may not be wound neatly, or sewing performance may suffer. In addition, extreme pressure may be applied to the bobbin, it may not be possible to remove the bobbin from the bobbin winder shaft, or the bobbin may break. 1 Guide slit in bobbin winder seat (with built-in cutter) Note • Be sure to wind the thread clockwise around the bobbin, otherwise the thread will become wrapped around the bobbin winder shaft. CAUTION • Be sure to cut the thread as described. If the bobbin is wound without cutting the thread using the cutter built into the guide slit in the bobbin winder seat, the thread may become tangled in the bobbin or the needle may bend or break when the bobbin thread starts to run out. Slide the sewing speed controller to adjust the bobbin g winding speed. Slide the controller to the right to increase the speed; slide it to the left to reduce the speed. When the bobbin winding becomes slow, press the j "Start/Stop" button once to stop the machine. When the foot controller is plugged in, remove your foot from the foot controller. CAUTION • When the bobbin winding becomes slow, stop the machine, otherwise the machine may be damaged. Cut the thread, slide the bobbin winder shaft to the left k until it snaps into place, and then remove the bobbin. Slide the sewing speed controller to desired sewing l speed position. Remove the spool for the bobbin thread from the spool m pin. Memo • We recommend winding stretch thread, such as transparent nylon thread, at a low speed since the thread may stretch. 15

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Winding/Installing the Bobbin
GETTING READY
15
1
e
Pass the thread under the hook on the bobbin winding
thread guide, and then wind it counterclockwise under
the pretension disk.
1
Bobbin winding thread guide
2
Pretension disk
3
Pull it in as far as possible
f
Wind the thread clockwise around the bobbin 5 or 6
times, pass the thread through the guide slit in the
bobbin winder seat, and then pull the thread to cut it.
1
Guide slit in bobbin winder seat
(with built-in cutter)
g
Slide the sewing speed controller to adjust the bobbin
winding speed. Slide the controller to the right to
increase the speed; slide it to the left to reduce the
speed.
h
Turn on the machine.
i
Press the “Start/Stop” button once to start winding the
bobbin.
When the foot controller is plugged in, press down on
the foot controller.
j
When the bobbin winding becomes slow, press the
“Start/Stop” button once to stop the machine.
When the foot controller is plugged in, remove your
foot from the foot controller.
k
Cut the thread, slide the bobbin winder shaft to the left
until it snaps into place, and then remove the bobbin.
l
Slide the sewing speed controller to desired sewing
speed position.
m
Remove the spool for the bobbin thread from the spool
pin.
Note
•
Make sure that the thread is passed under the
pretension disk.
Note
•
Be sure to wind the thread clockwise around the
bobbin, otherwise the thread will become wrapped
around the bobbin winder shaft.
CAUTION
•
Be sure to cut the thread as described. If the
bobbin is wound without cutting the thread
using the cutter built into the guide slit in the
bobbin winder seat, the thread may become
tangled in the bobbin or the needle may bend
or break when the bobbin thread starts to run
out.
Memo
•
We recommend winding stretch thread, such as
transparent nylon thread, at a low speed since the
thread may stretch.
1
2
3
a
Note
•
When winding transparent nylon thread on the bobbin,
stop bobbin winding when the bobbin is 1/2 to 2/3 full. If
the bobbin was fully wound with transparent nylon
thread, it may not be wound neatly, or sewing
performance may suffer. In addition, extreme pressure
may be applied to the bobbin, it may not be possible to
remove the bobbin from the bobbin winder shaft, or the
bobbin may break.
CAUTION
•
When the bobbin winding becomes slow, stop
the machine, otherwise the machine may be
damaged.