Brother International SE625 Operation Manual - Page 83

Checking machine operations

Get Brother International SE625 PDF manuals and user guides View all Brother International SE625 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

Use the cleaning brush or a vacuum cleaner mini i attachment to remove any lint or dust from the race and its surrounding area. 1 Cleaning brush 2 Race ba If the fabric could be removed. Continue with step p. If the fabric could not be removed. Continue with step j. Troubleshooting Remove any threads in the race and around the feed l dogs. Turn the handwheel to raise the feed dogs. m Align the two screw holes in the needle plate with the n two holes at the needle plate mounting base, and then fit the needle plate onto the machine. Lightly finger-tighten the screw on the right side of the o needle plate. Then, use the disc-shaped screwdriver to firmly tighten the screw on the left side. Finally, firmly tighten the screw on the right side. Note • Compressed can air is not recommended to be used. Use the included disc-shaped screwdriver to loosen the j two screws on the needle plate. Note • Be careful not to drop the removed screws in the machine. Slightly lift up the needle plate, cut any tangled k threads, and then remove the needle plate. Remove the fabric and threads from the needle plate. If the fabric cannot be removed, even after completing these steps, contact your nearest Brother authorized service center. Turn the handwheel to check that the feed dogs move smoothly and do not contact the edges of the slots in the needle plate. a b 1 Correct position of feed dogs 2 Incorrect position of feed dogs Insert the bobbin case by following step k in p "Cleaning the race" on page 77. Attach the needle plate cover according to step l in q "Cleaning the race" on page 77. Check the condition of the needle, and then install it. r If the needle is in a poor condition, for example, if it is bent, be sure to install a new needle. • Refer to "Checking the needle" on page 22 and "Replacing the needle" on page 22. Memo • Since the needle may have been damaged when the fabric was caught in the machine, we recommend replacing it with a new one. APPENDIX 5 ■ Checking machine operations If the needle plate has been removed, check machine operations to confirm that installation has been completed correctly. Turn on the machine. a Select stitch . b Note • Do not yet install the presser foot and thread. 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Troubleshooting
81
APPENDIX
5
i
Use the cleaning brush or a vacuum cleaner mini
attachment to remove any lint or dust from the race
and its surrounding area.
j
Use the included disc-shaped screwdriver to loosen the
two screws on the needle plate.
k
Slightly lift up the needle plate, cut any tangled
threads, and then remove the needle plate.
Remove the fabric and threads from the needle plate.
If the fabric cannot be removed, even after completing
these steps, contact your nearest Brother authorized
service center.
l
Remove any threads in the race and around the feed
dogs.
m
Turn the handwheel to raise the feed dogs.
n
Align the two screw holes in the needle plate with the
two holes at the needle plate mounting base, and then
fit the needle plate onto the machine.
o
Lightly finger-tighten the screw on the right side of the
needle plate. Then, use the disc-shaped screwdriver to
firmly tighten the screw on the left side. Finally, firmly
tighten the screw on the right side.
Turn the handwheel to check that the feed dogs move
smoothly and do not contact the edges of the slots in the
needle plate.
1
Correct position of feed dogs
2
Incorrect position of feed dogs
p
Insert the bobbin case by following step
k
in
“Cleaning the race” on page 77.
q
Attach the needle plate cover according to step
l
in
“Cleaning the race” on page 77.
r
Check the condition of the needle, and then install it.
If the needle is in a poor condition, for example, if it is
bent, be sure to install a new needle.
•
Refer to “Checking the needle” on page 22 and
“Replacing the needle” on page 22.
■
Checking machine operations
If the needle plate has been removed, check machine
operations to confirm that installation has been completed
correctly.
a
Turn on the machine.
b
Select stitch
.
1
Cleaning brush
2
Race
If the fabric could be removed.
Continue with step
p
.
If the fabric could not be removed.
Continue with step
j
.
Note
•
Compressed can air is not recommended to be used.
Note
•
Be careful not to drop the removed screws in the
machine.
a
b
Memo
•
Since the needle may have been damaged when the
fabric was caught in the machine, we recommend
replacing it with a new one.
Note
•
Do not yet install the presser foot and thread.
a
b