Canon DP-V2410 User Manual - Page 14

Mounting the Main Unit on a Stand or Wall

Get Canon DP-V2410 PDF manuals and user guides View all Canon DP-V2410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Mounting the Main Unit on a Stand or Wall This main unit can be fitted to a stand* or to a wall mount bracket*. Remove the stands beforehand ( 12). Screws compatible with this main unit are M4 x 7 mm (VESA Standard 100 x 100 mm). * Commercially available. CAUTION • For safety, make sure to perform this step with at least two people. • When mounting the main unit on a wall, make sure the wall has sufficient strength. If necessary, apply reinforcement. Also, make sure to check the load capacity of the stand or wall mount bracket. • When the video display is placed on a rack or display stand and ventilation around it is blocked by equipment placed above or below or in a surrounding area, the operating temperature may increase, causing a failure or overheating. In order to maintain the operating temperature condition of the video display (0 ˚C to 40 ˚C), make a space of at least 1U (4.4 cm) above and below and at least 4 cm space from its back. Make a sufficient space from peripheral equipment, secure vents, or install a ventilation fan. • When installing the video display on a wall, make sufficient space from the wall so that cables are not squeezed or twisted. • When mounting a commercially available stand or wall mount bracket, be sure that they do not contact the carrying handle. • Avoid touching the screen during this step as it may damage it. • Make sure that the main unit does not fall during installation/removal. 1. Attach a commercially available stand or wall mount bracket using four screw holes on the back or side face of the main unit ( 67). The screw hole size is shown below. 4×M4 7 mm deep (Max.) 2×M4 Rear 8 mm deep (Max.) Side Same on the other side 14 Installation/Connection

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
14
Installation/Connection
Mounting the Main Unit on a Stand or Wall
This main unit can be fitted to a stand* or to a wall mount bracket*. Remove the stands beforehand (
12).
Screws compatible with this main unit are M4 x 7 mm (VESA Standard 100 x 100 mm).
* Commercially available.
CAUTION
• For safety, make sure to perform this step with at least two people.
• When mounting the main unit on a wall, make sure the wall has sufficient strength. If necessary, apply reinforcement. Also,
make sure to check the load capacity of the stand or wall mount bracket.
• When the video display is placed on a rack or display stand and ventilation around it is blocked by equipment placed
above or below or in a surrounding area, the operating temperature may increase, causing a failure or overheating. In order
to maintain the operating temperature condition of the video display (0 ˚C to 40 ˚C), make a space of at least 1U (4.4 cm)
above and below and at least 4 cm space from its back. Make a sufficient space from peripheral equipment, secure vents,
or install a ventilation fan.
• When installing the video display on a wall, make sufficient space from the wall so that cables are not squeezed or twisted.
• When mounting a commercially available stand or wall mount bracket, be sure that they do not contact the carrying
handle.
• Avoid touching the screen during this step as it may damage it.
• Make sure that the main unit does not fall during installation/removal.
1. Attach a commercially available stand or wall mount bracket using four screw holes on the back or side
face of the main unit (
67).
The screw hole size is shown below.
Rear
4×M4
7 mm deep (Max.)
2×M4
8 mm deep (Max.)
Same on the other side
Side