Canon DP-V2410 User Manual - Page 86

Symptom, Cause and Action, Aspect Marker, Safety Zone Marker or

Get Canon DP-V2410 PDF manuals and user guides View all Canon DP-V2410 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

Symptom Cause and Action OSD menu cannot be used. • Check that "Protect Settings" is not set. 63 "Aspect Marker", " Safety Zone Marker " or • A channel with no signal, unsupported signal, or with "Input 65 "Area Marker" does not appear. Configuration" not set may be selected. Check the signal. The fan starts to rotate even when "Fan" • The fan stays off for approx. 1 minute when an AC power supply is used. 59 under "Camera Link" is set to "On" or To keep the fan off for a longer period, use a DC power supply. "Fan Stop" is set to "On". • When "Fan" under "Camera Link" is set to "On", the down time may not 63 match the camera. The fan does not stop even when "Fan" • The fan does not stop if the internal temperature of the video display is 59 under "Camera Link" is set to "On" or high. Configure settings after the internal temperature has lowered. "Fan Stop" is set to "On". • The fan may not stop in some conditions, for example when used at a 63 high temperature. Use the video display at the operating temperature ( 66) or lower. You forgot the password for "Protect • Press the jog dial and the button while the video display is in standby. 9 Settings". The configuration will be reset to the state where no password is set. The video display does not start up in the • Check the "Power on Setting" on the OSD menu. Set "Last memory" 64 condition that the power was turned off to start up the video display in the condition that the power is turned off last time. last time. 86 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
86
Troubleshooting
Symptom
Cause and Action
OSD menu cannot be used.
• Check that "Protect Settings" is not set.
63
"Aspect Marker", " Safety Zone Marker " or
"Area Marker" does not appear.
• A channel with no signal, unsupported signal, or with "Input
Configuration" not set may be selected. Check the signal.
65
The fan starts to rotate even when "Fan"
under "Camera Link" is set to "On" or
"Fan Stop" is set to "On".
• The fan stays off for approx. 1 minute when an AC power supply is used.
To keep the fan off for a longer period, use a DC power supply.
• When "Fan" under "Camera Link" is set to "On", the down time may not
match the camera.
59
63
The fan does not stop even when "Fan"
under "Camera Link" is set to "On" or
"Fan Stop" is set to "On".
• The fan does not stop if the internal temperature of the video display is
high. Configure settings after the internal temperature has lowered.
• The fan may not stop in some conditions, for example when used at a
high temperature. Use the video display at the operating temperature
(
66) or lower.
59
63
You forgot the password for "Protect
Settings".
• Press the jog dial and the
button while the video display is in standby.
The configuration will be reset to the state where no password is set.
9
The video display does not start up in the
condition that the power was turned off
last time.
• Check the "Power on Setting" on the OSD menu. Set "Last memory"
to start up the video display in the condition that the power is turned off
last time.
64