Canon DP-V2420 User Manual - Page 98

In the Multi View Dual display, the, Symptom, Cause and Action

Get Canon DP-V2420 PDF manuals and user guides View all Canon DP-V2420 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Symptom Cause and Action "Aspect Marker", " Safety Zone Marker " or • A channel with no signal, unsupported signal, or with "Input 74 "Area Marker" does not appear. Configuration" not set may be selected. Check the signal. The fan starts to rotate even when "Fan" • The fan operates to lower the temperature inside the main unit. The fan 68 under "Camera Link" is set to "On" or stops operating when the temperature inside has lowered. "Fan Stop" is set to "On". • When "Fan" under "Camera Link" is set to "On", the down time may not 70 match the camera. The fan does not stop even when "Fan" • The fan does not stop if the temperature inside the main unit is high. 68 under "Camera Link" is set to "On" or Configure settings after the internal temperature has lowered. "Fan Stop" is set to "On". • The fan may not stop in some conditions, for example when used at a 70 high temperature. Use the video display at the operating temperature ( 75) or lower. Loud fan noise • The fan operates at a faster speed than usual to lower the internal 70 temperature if "Fan Control" is set to "On" and when the temperature inside the main unit has increased. The fan operates at normal speed when "Fan Control" is set to "Off". • When high-luminance content is displayed continuously, the temperature inside the main unit rises even if the operating temperature is within the recommended range, and the fan operates at a faster speed than usual to lower the internal temperature. It is recommended to lower the brightness of the video display. You forgot the password for "Protect • Press the jog dial and the button while the video display is in standby. 12 Settings". The configuration will be reset to the state where no password is set. The video display does not start up in the • Check the "Power on Setting" on the OSD menu. Set "Last memory" 71 condition that the power was turned off to start up the video display in the condition that the power is turned off last time. last time. The image quality for the User mode in • Select the preset mode by "Copy Picture Mode" and copy the settings. 46 "Picture Mode" differs from the image quality of presets. In the "Multi View (Dual)" display, the • Check the settings of "Picture Mode", "Picture Function Target" under 50 image quality of the screens on the left "Channel Settings" or check the other settings for "Multi View (Dual)" 51 and right differ. display. 98 Troubleshooting

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
98
Troubleshooting
Symptom
Cause and Action
"Aspect Marker", " Safety Zone Marker " or
"Area Marker" does not appear.
• A channel with no signal, unsupported signal, or with "Input
Configuration" not set may be selected. Check the signal.
74
The fan starts to rotate even when "Fan"
under "Camera Link" is set to "On" or
"Fan Stop" is set to "On".
• The fan operates to lower the temperature inside the main unit. The fan
stops operating when the temperature inside has lowered.
• When "Fan" under "Camera Link" is set to "On", the down time may not
match the camera.
68
70
The fan does not stop even when "Fan"
under "Camera Link" is set to "On" or
"Fan Stop" is set to "On".
• The fan does not stop if the temperature inside the main unit is high.
Configure settings after the internal temperature has lowered.
• The fan may not stop in some conditions, for example when used at a
high temperature. Use the video display at the operating temperature
(
75) or lower.
68
70
Loud fan noise
• The fan operates at a faster speed than usual to lower the internal
temperature if "Fan Control" is set to "On" and when the temperature
inside the main unit has increased. The fan operates at normal speed
when "Fan Control" is set to "Off".
• When high-luminance content is displayed continuously, the temperature
inside the main unit rises even if the operating temperature is within
the recommended range, and the fan operates at a faster speed than
usual to lower the internal temperature. It is recommended to lower the
brightness of the video display.
70
You forgot the password for "Protect
Settings".
• Press the jog dial and the
button while the video display is in standby.
The configuration will be reset to the state where no password is set.
12
The video display does not start up in the
condition that the power was turned off
last time.
• Check the "Power on Setting" on the OSD menu. Set "Last memory"
to start up the video display in the condition that the power is turned off
last time.
71
The image quality for the User mode in
"Picture Mode" differs from the image
quality of presets.
• Select the preset mode by "Copy Picture Mode" and copy the settings.
46
In the "Multi View (Dual)" display, the
image quality of the screens on the left
and right differ.
• Check the settings of "Picture Mode", "Picture Function Target" under
"Channel Settings" or check the other settings for "Multi View (Dual)"
display.
50
51