Canon XA45 XA40 XA45 Instruction Manual - Page 98

Rec Command] and [HDMI Time Code] to, only or [HDMI Scan Mode]

Get Canon XA45 PDF manuals and user guides View all Canon XA45 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 98 highlights

Connecting to an External Monitor NOTES • The HDMI OUT terminal on the camcorder is for output only. Do not connect it to an HDMI output terminal on an external device, as this may damage the camcorder. • Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors. • Video may not be output correctly depending on the monitor. • If the connected monitor is not compatible with the signal output from the camcorder, then HDMI 98 output will stop. • The time code signal will not be output from the HDMI OUT terminal in the following cases. - In mode. - When slow & fast motion recording is activated. - When the output is 720x480 / 59.94P. • The frames value in the time code will run from 0 to 29 instead of 0 to 23 in the following cases. - > [£ Display Setup] > [SDI/HDMI Scan Mode] (s only) or [HDMI Scan Mode] (t only) is [ PsF (Forced 1080i)] and the frame rate is 23.98P. - When the output is 1280x720. • You can set both > [3 Recording Setup] > [Rec Command] and [HDMI Time Code] to [i On] to use the camcorder's START/STOP button to control also the recording operation of an external recorder connected to the HDMI OUT terminal. The camcorder's time code signal will be output as well.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
Connecting to an External Monitor
98
NOTES
•
The HDMI OUT terminal on the camcorder is for output only. Do not connect it to an HDMI output
terminal on an external device, as this may damage the camcorder.
•
Correct operation cannot be guaranteed when connecting the camcorder to DVI monitors.
•
Video may not be output correctly depending on the monitor.
•
If the connected monitor is not compatible with the signal output from the camcorder, then HDMI
output will stop.
•
The time code signal will not be output from the HDMI OUT terminal in the following cases.
- In
mode.
-
When slow & fast motion recording is activated.
-
When the output is 720x480 / 59.94P.
•
The frames value in the time code will run from 0 to 29 instead of 0 to 23 in the following cases.
-
>
[
£
Display Setup]
>
[SDI/HDMI Scan Mode] (
s
only) or [HDMI Scan Mode]
(
t
only) is [
PsF (Forced 1080i)] and the frame rate is 23.98P.
-
When the output is 1280x720.
•
You can set both
>
[
3
Recording Setup]
>
[Rec Command] and [HDMI Time Code] to
[
i
On] to use the camcorder’s START/STOP button to control also the recording operation of an
external recorder connected to the HDMI OUT terminal. The camcorder’s time code signal will be
output as well.