Cisco MWR-1941-DC-2T1 Hardware Installation Guide - Page 42

Rack Mounting the Chassis

Get Cisco MWR-1941-DC-2T1 - MWR 1941 Mobile Wireless Edge Router PDF manuals and user guides View all Cisco MWR-1941-DC-2T1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 42 highlights

Rack Mounting the Chassis Chapter 3 Installing the Router For WICs: • Quick Start Guide: Interface Cards for Cisco 1600, 1700, 2600, 3600, 3700 Series, and Cisco MWR 1941-DC Routers • Cisco Interface Cards Hardware Installation Guide If there are modules, interface cards, or power supplies to be removed or installed, Cisco suggests that you perform the installation or removal before you install the chassis. If a chassis cover needs to be removed, the chassis may have to be removed from the rack to permit cover removal. Rack Mounting the Chassis You can mount the Cisco MWR 1941-DC router in a 19-inch rack that conforms to EIA-310-D specification (the inside width of the rack should be 17.72 to 17.80 inches per the EIA-310-D specification). The MWR 1941-DC router requires this minimum width and occupies 1U (1.75 inches) of vertical space. Warning To prevent bodily injury when mounting or servicing this unit in a rack, you must take special precautions to ensure that the system remains stable. The following guidelines are provided to ensure your safety: • This unit should be mounted at the bottom of the rack if it is the only unit in the rack. • When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest component at the bottom of the rack. • If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the rack Attaching the Brackets Attach the mounting brackets to the chassis as shown, using the screws provided in the bracket kit. Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to install the bracket screws. Three screws are required on each side. Figure 3-1 shows how the bracket is attached. Cisco MWR 1941-DC Mobile Wireless Edge Router Hardware Installation Guide 3-2 78-15827-06B0

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
3-2
Cisco MWR 1941-DC Mobile Wireless Edge Router Hardware Installation Guide
78-15827-06B0
Chapter 3
Installing the Router
Rack Mounting the Chassis
For WICs:
•
Quick Start Guide: Interface Cards for Cisco 1600, 1700, 2600, 3600, 3700 Series, and Cisco
MWR 1941-DC Routers
•
Cisco Interface Cards Hardware Installation Guide
If there are modules, interface cards, or power supplies to be removed or installed, Cisco suggests that
you perform the installation or removal before you install the chassis. If a chassis cover needs to be
removed, the chassis may have to be removed from the rack to permit cover removal.
Rack Mounting the Chassis
You can mount the Cisco MWR 1941-DC router in a 19-inch rack that conforms to EIA-310-D
specification (the inside width of the rack should be 17.72 to 17.80 inches per the EIA-310-D
specification). The MWR 1941-DC router requires this minimum width and occupies 1U (1.75 inches)
of vertical space.
Warning
To prevent bodily injury when mounting or servicing this unit in a rack, you must take special
precautions to ensure that the system remains stable. The following guidelines are provided to ensure
your safety:
•
This unit should be mounted at the bottom of the rack if it is the only unit in the rack.
•
When mounting this unit in a partially filled rack, load the rack from the bottom to the top with the heaviest
component at the bottom of the rack.
•
If the rack is provided with stabilizing devices, install the stabilizers before mounting or servicing the unit in the
rack
Attaching the Brackets
Attach the mounting brackets to the chassis as shown, using the screws provided in the bracket kit.
Attach the second bracket to the opposite side of the chassis. Use a number 2 Phillips screwdriver to
install the bracket screws.
Three screws are required on each side.
Figure 3-1
shows how the bracket is attached.