Cisco VG204 Software Configuration Guide - Page 29

Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways

Get Cisco VG204 PDF manuals and user guides View all Cisco VG204 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Chapter 4 Configuring Voice Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways Step 6 Step 7 Step 8 Step 9 VG(config)# ip routing For complete information about global configuration commands, see the Cisco IOS configuration guides and command references. To configure another interface, enter the exit command to return to the VG(config)# prompt. To configure the Cisco VG for voice traffic, see the VoIP references in the "Prerequisites" section on page 4-1. To exit configuration mode and return to the enable prompt, when you finish configuring interfaces, press Ctrl-Z. To see the current operating configuration, including any changes you just made, enter the show running-config command: VG# show running-config To see the configuration currently stored in NVRAM, enter the show startup-config command at the enable prompt: VG# show startup-config The results of the show running-config and show startup-config commands differ if you have made changes to the configuration but have not yet written them to NVRAM. To write your changes to NVRAM and make them permanent, enter the copy running-config startup-config command at the enable prompt: VG# copy running-config startup-config Building configuration. . . [OK] VG# The Cisco VG is now configured to boot in the new configuration. Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways To configure auto-configuration on the Cisco VG202 and Cisco VG204 voice gateways, follow these guidelines and procedures: • Restrictions for Configuring Auto-Configuration • Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways • Configuring the Voice Interface for Cisco CallManager • Configuring the MAC Address Convention Restrictions for Configuring Auto-Configuration The following restrictions apply to configuring auto-configuration on the Cisco VG202 and Cisco VG204 voice gateways before connecting them to the network: • The Cisco Unified Communications Manager (CCM) needs to be provisioned with the voice gateway information. OL-16191-01 Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide 4-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
4-3
Cisco VG202 and Cisco VG204 Voice Gateways Software Configuration Guide
OL-16191-01
Chapter 4
Configuring Voice
Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways
VG(config)#
ip routing
For complete information about global configuration commands, see the Cisco IOS configuration guides
and command references.
Step 6
To configure another interface, enter the
exit
command to return to the
VG(config)#
prompt.
Step 7
To configure the Cisco VG for voice traffic, see the VoIP references in the
“Prerequisites” section on
page 4-1
.
Step 8
To exit configuration mode and return to the enable prompt, when you finish configuring interfaces,
press
Ctrl-Z
. To see the current operating configuration, including any changes you just made, enter the
show running-config
command:
VG#
show running-config
To see the configuration currently stored in NVRAM, enter the
show startup-config
command
at the
enable prompt:
VG#
show startup-config
Step 9
The results of the
show running-config
and
show startup-config
commands differ if you have made
changes to the configuration but have not yet written them to NVRAM. To write your changes to
NVRAM and make them permanent, enter the
copy running-config startup-config
command at the
enable prompt:
VG#
copy running-config startup-config
Building configuration. . .
[OK]
VG#
The Cisco VG is now configured to boot in the new configuration.
Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice
Gateways
To configure auto-configuration on the Cisco VG202 and Cisco VG204 voice gateways, follow these
guidelines and procedures:
•
Restrictions for Configuring Auto-Configuration
•
Auto-Configuration on the Cisco VG202 and Cisco VG204 Voice Gateways
•
Configuring the Voice Interface for Cisco CallManager
•
Configuring the MAC Address Convention
Restrictions for Configuring Auto-Configuration
The following restrictions apply to configuring auto-configuration on the Cisco VG202 and Cisco
VG204 voice gateways before connecting them to the network:
•
The Cisco Unified Communications Manager (CCM) needs to be provisioned with the voice
gateway information.