Cisco WS-C3560X-48PF-L Hardware Installation Guide - Page 108

If you want to save the configuration and use it the next time the switch reboots, select option 2

Get Cisco WS-C3560X-48PF-L PDF manuals and user guides View all Cisco WS-C3560X-48PF-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

Entering the Initial Configuration Information Appendix C Configuring the Switch with the CLI-Based Setup Program If you enter N, the switch appears as a candidate switch in the Network Assistant GUI. You can configure the switch as a command switch later through the CLI, the device manager, or the Network Assistant application. To configure it later, enter no. Would you like to enable as a cluster command switch? [yes/no]: no You have completed the initial configuration of the switch, and the switch displays its configuration. This is an example of the configuration output: The following configuration command script was created: hostname switch1 enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1 enable password enable_password line vty 0 15 password terminal-password no snmp-server ! no ip routing ! interface Vlan1 no shutdown ip address 10.4.120.106 255.0.0.0 ! interface GigabitEthernet1/0/1 ! interface GigabitEthernet1/0/2 interface GigabitEthernet1/0/3 ! ... ! interface GigabitEthernet1/0/23 ! end Step 10 These choices appear: [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. If you want to save the configuration and use it the next time the switch reboots, select option 2 to save it in nonvolatile RAM (NVRAM). Enter your selection [2]:2 Make your selection, and press Return. After you complete the setup program, the switch can run the default configuration that you created. To change this configuration or to perform other management tasks, enter commands at the Switch> prompt or use Cisco Network Assistant, the Cluster Management Suite (CMS), or another management tool for further configuration. Catalyst 3750-X and 3560-X Switch Hardware Installation Guide C-8 OL-19593-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
C-8
Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
OL-19593-02
Appendix C
Configuring the Switch with the CLI-Based Setup Program
Entering the Initial Configuration Information
If you enter
N
, the switch appears as a candidate switch in the Network Assistant GUI. You can configure
the switch as a command switch later through the CLI, the device manager, or the Network Assistant
application. To configure it later, enter
no
.
Would you like to enable as a cluster command switch? [yes/no]:
no
You have completed the initial configuration of the switch, and the switch displays its configuration.
This is an example of the configuration output:
The following configuration command script was created:
hostname switch1
enable secret 5 $1$Ulq8$DlA/OiaEbl90WcBPd9cOn1
enable password
enable_password
line vty 0 15
password
terminal-password
no snmp-server
!
no ip routing
!
interface Vlan1
no shutdown
ip address 10.4.120.106 255.0.0.0
!
interface GigabitEthernet1/0/1
!
interface GigabitEthernet1/0/2
interface GigabitEthernet1/0/3
!
...<output abbreviated>
!
interface GigabitEthernet1/0/23
!
end
Step 10
These choices appear:
[0] Go to the IOS command prompt without saving this config.
[1] Return back to the setup without saving this config.
[2] Save this configuration to nvram and exit.
If you want to save the configuration and use it the next time the switch reboots, select option 2 to
save it in nonvolatile RAM (NVRAM).
Enter your selection [2]:
2
Make your selection, and press
Return
.
After you complete the setup program, the switch can run the default configuration that you created. To
change this configuration or to perform other management tasks, enter commands at the
Switch>
prompt
or use Cisco Network Assistant, the Cluster Management Suite (CMS), or another management tool for
further configuration.