Cisco WS-C3560X-48PF-L Hardware Installation Guide - Page 58

Removing a Network Module, Installing SFP and SFP+ Modules

Get Cisco WS-C3560X-48PF-L PDF manuals and user guides View all Cisco WS-C3560X-48PF-L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Installing SFP and SFP+ Modules Figure 2-22 Installing the Network Module in the Switch Chapter 2 Switch Installation 253156 C3KX-NM-10G NMEOTWDUOLREK G1 G2/TE1 G3 G4/TE2 37 38 39 4 56 78 9 10 11 12 Caution Do not install the converter module with connected SFP modules or cables. Always remove any cables and modules before installing the converter module in the slot. Removing a Network Module Step 1 Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface. Caution Do not remove the network module with installed SFP modules or cables. Always remove any cables and modules before removing the network module from the slot. Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Disconnect the cables from the SFP module. Remove the SFP modules from the network module. Loosen the captive screws that hold the network module in place. Carefully press the tab on the right side of the network module to release it from the slot. Grasp the edges of the module, and carefully slide it out of the slot. Install a replacement network module or a blank module in the slot. Place the module that you removed in an antistatic bag or other protective environment. Installing SFP and SFP+ Modules This section describes how to install and remove SFP modules in the switch and in the network module. See the "SFP and SFP+ Modules" section on page 1-7 and the switch release notes on Cisco.com for the list of SFP modules that the switch supports. Use only Cisco SFP modules on the switch. For more information about installing, removing, cabling, and troubleshooting SFP modules, see the module documentation that shipped with your device. For module cable specifications, see Appendix B, "Connector and Cable Specifications." 2-24 Catalyst 3750-X and 3560-X Switch Hardware Installation Guide OL-19593-02

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
2-24
Catalyst 3750-X and 3560-X Switch Hardware Installation Guide
OL-19593-02
Chapter 2
Switch Installation
Installing SFP and SFP+ Modules
Figure 2-22
Installing the Network Module in the Switch
Caution
Do not install the converter module with connected SFP modules or cables. Always remove any cables
and modules before installing the converter module in the slot.
Removing a Network Module
Step 1
Attach an ESD-preventive wrist strap to your wrist and to a bare metal surface.
Caution
Do not remove the network module with installed SFP modules or cables. Always remove any cables
and modules before removing the network module from the slot.
Step 2
Disconnect the cables from the SFP module.
Step 3
Remove the SFP modules from the network module.
Step 4
Loosen the captive screws that hold the network module in place.
Step 5
Carefully press the tab on the right side of the network module to release it from the slot. Grasp the edges
of the module, and carefully slide it out of the slot.
Step 6
Install a replacement network module or a blank module in the slot.
Step 7
Place the module that you removed in an antistatic bag or other protective environment.
Installing SFP and SFP+ Modules
This section describes how to install and remove SFP modules in the switch and in the network module.
See the
“SFP and SFP+ Modules” section on page 1-7
and the switch release notes on Cisco.com for the
list of SFP modules that the switch supports. Use only Cisco SFP modules on the switch.
For more information about installing, removing, cabling, and troubleshooting SFP modules, see the
module documentation that shipped with your device. For module cable specifications, see
Appendix B,
“Connector and Cable Specifications.”
253156
3
7
38
3
9
4
5
6
7
8
9
10
11
12
C
3
KX-NM-10G
NETWORK
MODULE
G1
G2/TE1
G
3
G4/TE2