Craftsman 28974 Operation Manual - Page 20

TRACTOR Always observe safety rules when performing any maintenance. BRAKE OPERATION ROS "ON" Position Engine "ON" Position (Normal Operating) If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See "TO CHECK BRAKE" in the Service and Adjustments section of this manual). TIRES , Maintain proper air pressure in all tires (See PSI on tires). = Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to stow leaks, tire sealant may be purchased from your local parts dealer. Tire sealant also prevents tire dry rot and corrosion. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROe) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should notstart unlessthe brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM - When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. , When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. o The attachment clutch should never operate unless the operator is in the seat. CHECK REVERSE OPERATION (ROS) SYSTEM - When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine. ° When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine. BLADE CARE For best results mower blades must be sharp. Replace worn, bent or damaged blades. CAUTION: Use only a replacement blade approved by the manufacturer of your tractor. Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. BLADE REMOVAL 1. Raise mower to highest position to allow access to blades. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. 2. Remove blade bolt by turning counter- clockwise. 3. Install new blade with stamped "GRASS SIDE" facing the ground. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. 4. Install and tighten blade bolt securely (45-55 Ft. Lbs. torque). IMPORTANT: Special blade bolt is heat treated. Blade Blade (Special) X,_.. Mandrel Assembly iStar Center Hole BATTERY Your tractor has a battery charging system which is sufficient for normal use. How- ever, periodic charging of the battery with an automotive charger will extend its life. , Keep battery and terminals clean. • Keep battery bolts tight. • Keep small vent holes open. , Recharge at 6q0 amperes for I hour. NOTE: The original equipment battery on your tractor is maintenance free. Do not attempt to open or remove caps or covers. Adding or checking level of electrolyte is not necessary. 2O ij_kPRECAUCl puede que de las ruedas, 4, Apretar el el rondo, rr soltar el pe atr&s hast_ (5) segund procedimi_ 5. Apague el estacionar 6. Enganche control de conducir 0 esta secci_ 7. Sentado e el motor. E motor, mu_ media (1/2 mano 8. Conduzca aproximao hacia mar= Repita est Su transmisi61 para la opera( CONSEJOS • No se pued Ilantas cua_ adjunta al t_ • La segador adecuada al segar. V, LA SEGAD Ajustes de • El lado izqt usar para rl • Maneje de arguen en Mantenga € del tractor. m&s pareja uniforme. • AI segar la.' a ta derech descarguer cos, entrad de una o d_ opuesta, hl hasta qua 1