Cub Cadet CC 760ES CC 760ES Operator's Manual - Page 23

Service - belt

Get Cub Cadet CC 760ES PDF manuals and user guides View all Cub Cadet CC 760ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Service Cutting Deck Removal Warning! Before performing any maintenance or repairs, disengage blades, stop engine and remove key if so equipped to prevent unintended starting. To remove the cutting deck, proceed as follows: 1. Remove the belt cover by removing the three screws and washers which secure it to the frame. See Fig. 7-1. WARNING: Do not operate mower without the belt cover installed. Failure to follow this instruction could result in personal injury or property damage. 7 Figure 7-2 6. Remove the belt keeper rod and remove the deck belt from around the mower's engine pulley. 7. Looking at the cutting deck from the left side, locate and carefully remove the hairpin clips that secure the deck supports on the rear left side and front left side of the deck. See Fig. 7-3. 8. Repeat the previous step on the mower's right side. 9. Carefully remove the front deck supports from the deck lift arms. See Fig. 7-3. Figure 7-1 2. Place the deck height lever in its highest position. 3. Position wood blocks at various places under the deck's edge. These will temporarily support the deck as you unmount it. 4. Use the deck height lever to lower the deck, so that it rests on the wood blocks. 5. Remove the screw and flange nut which secures the belt keeper rod to the left side of the mower's frame. See Fig. 7-2. Lift Arm Figure 7-3 23

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Cutting Deck Removal
WARNING!
Before performing any maintenance or
repairs, disengage blades, stop engine and remove
key if so equipped to prevent unintended starting.
To remove the cutting deck, proceed as follows:
Remove the belt cover by removing the three screws and
1.
washers which secure it to the frame. See Fig. 7-1.
WARNING:
Do not operate mower without the
belt cover installed. Failure to follow this instruction
could result in personal injury or property damage.
Place the deck height lever in its highest position.
2.
Position wood blocks at various places under the deck’s
3.
edge. These will temporarily support the deck as you
unmount it.
Use the deck height lever to lower the deck, so that it rests
4.
on the wood blocks.
Remove the screw and flange nut which secures the belt
5.
keeper rod to the left side of the mower’s frame.
See Fig. 7-2.
Remove the belt keeper rod and remove the deck belt from
6.
around the mower’s engine pulley.
Looking at the cutting deck from the left side, locate and
7.
carefully remove the hairpin clips that secure the deck
supports on the rear left side and front left side of the deck.
See Fig. 7-3.
Repeat the previous step on the mower’s right side.
8.
Carefully remove the front deck supports from the deck lift
9.
arms. See Fig. 7-3.
Figure 7-1
Figure 7-2
Figure 7-3
Lift Arm
Service
7
23