Cub Cadet ZTX4 60 Operation Manual - Page 22

SERVICE AND MAINTENANCE Leveling the Deck (Side-to-Side) 1. Park the tractor on a firm, level surface. 2. Ensure that all tires are properly inflated. 3. Place the deck lift knob in a middle mowing position and rotate both outside b. Rotate both front nuts clockwise to raise the front deck pitch or counter-clockwise to lower the front deck pitch, depending on the needed adjustment. Adjust each nut equally. See Figure 43. Note: Make adjustments in quarter-turn increments, and remeasure front-to-reardeck pitch blade distance frequently until proper pitch is achieved. blades so that they are perpendicular with the tractor. c. Reinstall the end caps onto the deck rods. 4. Measure the distance from the outside of the left blade tip to the ground Adjusting the Deck Wheels and the distance from the outside of the right blade tip to the ground. Both measurements taken should be equal. If they're not, proceed to the next step. WARNING 5. Locate the Keep hands and feet away from the discharge opening of the cutting deck. adjustment nuts on top of the deck lift rods on the left and right side of the tractor. There is one on each side at the front of the deck between the platform Lower Frame Not Shown for Clarity and lower frame tube, Figure 42 and one at each side of the rear of the deck near the front of the rear wheel. See Figure 42. Note: The deck wheels are an anti-scalp feature of the deck and are not designed to support the weight of the cutting deck. The deck wheels should be approximately 6.35-12.7 mm)above the ground when the deck is set in the desired height setting. To adjust the deck wheels see the Assembly & Set-Up section for instructions. Lapbar Drive Control Lever Stop Adjustment When the lapbar drive control levers are both fully extended forward to the fullspeed position and the tractor drifts left or right, the lapbar drive control lever stop adjustment can be adjusted to sync the wheel speeds. To perform the adjustment, proceed as follows: 1. Identify the side that the tractor is drifting to and adjust the opposite lapbar drive control lever. If the tractor 6. Remove the end cap from front deck lift rods and save for later re- drifts right, adjust the installation. left lapbar drive control 7. Rotate either the left side (front and rear) or right side (front and rear) nuts clockwise to raise the deck height or counter-clockwise to lower the deck, lever down (decrease speed) and vice versa. depending on the needed adjustment. Adjust each nut equally. 2. Locate the lapbar drive Note: Make adjustments in quarter-turn increments, and remeasure blade distance control lever stop adjustment bolts (a) on both sides frequently. on the front of the seat Leveling the Deck (Pitch/Front-to-Rear) frame. See Figure 44. (a) Figure 44 The front of the deck should be between 3-9 mm) lower than the rear of the Note: The multi-tool (if equipped) can be used to make this adjustment. deck. Adjust if necessary as follows: 3. To decrease the forward speed, turn the lapbar drive control lever stop 1. Park the tractor on a firm, level surface and place the deck lift knob in a middle position. 2. Ensure that all tires are properly inflated. 3. Ensure side-to-side level. 4. Rotate the blade nearest the discharge chute so that it is parallel with the tractor. 5. Measure the distance from the front of the blade tip to the ground and the rear of the blade tip to the ground. The first measurement taken should be between 3-9 mm) less than the second measurement. 6. Determine the approximate distance necessary for proper adjustment and proceed, if necessary. a. Remove the end cap on Figure 43 adjustment bolts (a) clockwise. To increase the forward speed, turn the lapbar drive control lever stop adjustment bolts (a) counter-clockwise. Turn the lapbar drive control lever stop adjustment bolts (a) in the necessary direction ⁄-turn at a time. After turning the lapbar drive control lever stop adjustment bolts (a), check the adjustment by driving the tractor. 4. Continue the adjustment until the wheel speeds are in sync and the tractor drives straight with the drive control levers fully extended forward in the full-speed position. Note: Make sure the bolts extend through the nuts on the frame to engage the locking feature. Service Electrical System A fuse is installed to protect the tractor's electrical system from damage caused by excessive amperage. Always use the same capacity fuse for replacement. If the electrical system does not function, check for a blown fuse. If you have a recurring problem with blown fuses, have the tractor's electrical system checked by your authorized service dealer. Relays and Switches There are several safety switches in the electrical system. If a function of the safety interlock system described earlier is not functioning properly, have the electrical system checked by your authorized service dealer. both front deck height adjust rods and save for later re-installation. See Figure 43. 22