D-Link 1226G User Manual - Page 8

Configuration - switch des

Get D-Link 1226G - DES Switch PDF manuals and user guides
UPC - 790069264221
View all D-Link 1226G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 8 highlights

Use the screws provided. Then, use the screws provided with the equipment rack to mount the Switch in the rack. Mount the Switch in the rack. Connecting Network Cable The DES-1226G supports 10/100/1000Mbps Gigabit Ethernet. It runs full-/half- duplex transfer mode for 10/100Mbps and full-duplex transfer mode for 1000Mbps. Each port on the DES-1226G supports Auto-MDI/MDI-X. Auto-MDI/MDI-X is a feature that eliminates the need for worrying about using either a standard or crossover cable-you can use either one-and allows any port to be an uplink port. AC Power The DES-1226G can be used with AC power supply 100~240V AC, 50~60 Hz. The power switch is located at the rear of the unit adjacent to the AC power connector and the system fan. The Switch's power supply will adjust to the local power source automatically and may be turned on without having any or all LAN segment cables connected. 4. Configuration Through the Web browser you can configure Switch settings such as VLAN, Trunking, QoS... etc. Using the Switch's Web Management Utility, you can easily discover all the D-Link Web-Smart Switches in your network, assign the IP Address, change the password, and upgrade new firmware. Installing the Web Management Utility The following gives instructions guiding you through the installations of the Web Management utility. 1. Insert the Utility CD in the CD-Rom Drive. 2. From the Start menu on the Windows desktop, choose Run. 3. In the Run dialog box, type D:\Web Management Utility\setup.exe (D:\ depends where your CD-Rom drive is located) and click OK. 4. Follow the on-screen instructions to install the utility. 5. Upon completion, go to Program Files -> web_management_utility and execute the Web Management utility. (Figure 1.) 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
Use the screws provided.
Then, use the screws provided with the equipment rack to mount the Switch in the rack.
Mount the Switch in the rack.
Connecting Network Cable
The DES-1226G supports 10/100/1000Mbps Gigabit Ethernet. It runs full-/half- duplex transfer mode for 10/100Mbps
and full-duplex transfer mode for 1000Mbps. Each port on the DES-1226G supports Auto-MDI/MDI-X. Auto-MDI/MDI-X
is a feature that eliminates the need for worrying about using either a standard or crossover cable—you can use either
one—and allows any port to be an uplink port.
AC Power
The DES-1226G can be used with AC power supply 100~240V AC, 50~60 Hz. The power switch is located at the rear
of the unit adjacent to the AC power connector and the system fan. The Switch’s power supply will adjust to the local
power source automatically and may be turned on without having any or all LAN segment cables connected.
4.
Configuration
Through the Web browser you can configure Switch settings such as VLAN, Trunking, QoS… etc.
Using the Switch’s Web Management Utility, you can easily discover all the D-Link
Web-Smart Switches in your
network, assign the IP Address, change the password, and upgrade
new firmware.
Installing the Web Management Utility
The following gives instructions guiding you through the installations of the Web Management utility.
1.
Insert the Utility CD in the CD-Rom Drive.
2. From the
Start
menu on the Windows desktop, choose
Run
.
3. In the
Run
dialog box, type D:\Web Management Utility\setup.exe (D:\ depends where your CD-Rom drive is
located) and click
OK
.
4.
Follow the on-screen instructions to install the utility.
5.
Upon completion, go to
Program Files -> web_management_utility
and execute the Web Management utility.
(Figure 1.)
8