D-Link DES-3624 Product Manual - Page 23

CONNECTING THE SWITCH, Switch to End Node, Switch to Hub or Switch

Get D-Link DES-3624 - Switch - Stackable PDF manuals and user guides
UPC - 790069221736
View all D-Link DES-3624 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Stackable NWay Ethernet Switch User's Guide 4 4 CONNECTING THE SWITCH This chapter describes how to connect the Switch to your Ethernet network. Switch to End Node End nodes include PCs outfitted with a 10, 100 or 10/100 Mbps RJ-45 Ethernet/Fast Ethernet Network Interface Card (NIC) and most routers. The RJ-45 UTP ports on NICs and most routers are MDI-II. When using a normal straight-through cable, an MDI-II port must connect to an MDI-X port. An end node can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable (be sure to use Category 5 UTP or STP cabling for 100 Mbps Fast Ethernet connections). The end node should be connected to any of the twenty-two ports (1x - 22x) of the Switch or to either of the two 100BASE-TX ports on the front-panel module that came preinstalled on the Switch. An end node should not be connected to an Uplink port (unless using a crossover cable), and if the top Uplink port is in use, Port 1x must remain vacant; if the bottom Uplink port is in use, Port 2x cannot be used. Figure 4-1. Switch connected to an End Node The LED indicators for the port the end node is connected to are lit according to the capabilities of the NIC. If LED indicators are not illuminated after making a proper connection, check the PC's LAN card, the cable, switch conditions, and connections. The following LED indicator states are possible for an end node to switch connection: 1. The 100M LED indicator comes ON for a 100 Mbps and stays OFF for 10 Mbps. 2. The Link/Act LED indicator lights up upon hooking up a PC that is powered on. Switch to Hub or Switch These connections can be accomplished in a number of ways. The most important consideration is that when using a normal, straight-through cable, the connection should be made between a normal crossed port (Port 1x, 2x, etc.) and an Uplink (MDI-II) port. If you are using a crossover cable, the connection must be made from Uplink to Uplink, or from a crossed port to another crossed port. Connecting The Switch 27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
Stackable NWay Ethernet Switch User’s Guide
Connecting The Switch
27
4
4
C
ONNECTING
T
HE
S
WITCH
This chapter describes how to connect the Switch to your Ethernet network.
Switch to End Node
End nodes include PCs outfitted with a 10, 100 or 10/100 Mbps RJ-45 Ethernet/Fast Ethernet Network
Interface Card (NIC) and most routers. The RJ-45 UTP ports on NICs and most routers are MDI-
II
. When
using a normal straight-through cable, an MDI-
II
port must connect to an MDI-
X
port.
An end node can be connected to the Switch via a two-pair Category 3, 4, 5 UTP/STP straight cable (be sure to
use Category 5 UTP or STP cabling for 100 Mbps Fast Ethernet connections). The end node should be
connected to any of the twenty-two ports (1x - 22x) of the Switch or to either of the two 100BASE-TX ports on
the front-panel module that came preinstalled on the Switch. An end node should not be connected to an
Uplink port (unless using a crossover cable), and if the top Uplink port is in use, Port 1x must remain vacant;
if the bottom Uplink port is in use, Port 2x cannot be used.
Figure 4-1.
Switch connected to an End Node
The LED indicators for the port the end node is connected to are lit according to the capabilities of the NIC. If
LED indicators are not illuminated after making a proper connection, check the PC’s LAN card, the cable,
switch conditions, and connections.
The following LED indicator states are possible for an end node to switch connection:
1.
The 100M LED indicator comes
ON
for a 100 Mbps and stays
OFF
for 10 Mbps.
2.
The Link/Act LED indicator lights up upon hooking up a PC that is powered on.
Switch to Hub or Switch
These connections can be accomplished in a number of ways. The most important consideration is that when
using a normal, straight-through cable, the connection should be made between a normal crossed port (Port
1x, 2x, etc.) and an Uplink (MDI-
II
) port. If you are using a crossover cable, the connection must be made from
Uplink to Uplink, or from a crossed port to another crossed port.