Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 13

To con switch ports, From Port / To Port, State, Speed/Duplex, Parameter, Description

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide Figure 5-3 Port Settings window To configure switch ports: 1. Choose the port or sequential range of ports using the From Port and To Port drop-down menus. 2. Use the remaining drop-down menus to configure the parameters described below: The fields that can be configured are described below: Parameter Description From Port / To Port Use the drop-down menu to select the port range to be configured. State Toggle the State field to either enable or disable a given port or group of ports. Speed/Duplex Toggle the Speed/Duplex field to select the speed and full-duplex/half-duplex state of the port. Auto denotes auto-negotiation among 10, 100 and 1000 Mbps devices, in full- or half-duplex (except 1000 Mbps which is always full duplex). The Auto setting allows the port to automatically determine the fastest settings the device the port is connected to can handle, and then to use those settings. The other options are 10M Half, 10M Full, 100M Half, 100M Full, 1000M Full_Master, 1000M Full_Slave, and 1000M Full. There is no automatic adjustment of port settings with any option other than Auto. The Switch allows the user to configure three types of gigabit connections; 1000M Full_Master, 1000M Full_Slave, and 1000M Full. Gigabit connections only support full duplex connections and take on certain characteristics that are different from the other choices listed. The 1000M Full_Master and 1000M Full_Slave parameters refer to connections running a 1000BASE-T cable for connection between the Switch port and other device capable of a gigabit connection. The master setting (1000M Full_Master) will allow the port to advertise capabilities related to duplex, speed and physical layer type. The master setting will also determine the master and slave relationship between the two connected physical layers. This relationship is necessary for establishing the timing control between the two physical layers. The timing control is set on a master physical layer by a local source. The slave setting (1000M Full_Slave) uses loop timing, where the timing comes 8

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

Figure 5-3 Port Settings window

To configure switch ports:

Choose the port or sequential range of ports using the From Port and To Port drop-down menus.

Use the remaining drop-down menus to configure the parameters described below:

The fields that can be configured are described below:

Parameter

Description

From Port / To Port

Use the drop-down menu to select the port range to be configured.

State

Toggle the State field to either enable or disable a given port or group of ports.

Speed/Duplex

Toggle the Speed/Duplex

field to select the speed and full-duplex/half-duplex state of the

port.

Auto

denotes auto-negotiation among 10, 100 and 1000 Mbps devices, in full- or

half-duplex (except 1000 Mbps which is always full duplex). The

Auto

setting allows the

port to automatically determine the fastest settings the device the port is connected to

can handle, and then to use those settings. The other options are

10M Half

10M Full,

100M Half

100M Full

1000M Full_Master

1000M Full_Slave, and 1000M Full

. There is

no automatic adjustment of port settings with any option other than

Auto

The Switch allows the user to configure three types of gigabit connections;

1000M

Full_Master

1000M Full_Slave

, and

1000M Full

. Gigabit connections only support full

duplex connections and take on certain characteristics that are different from the other

choices listed.

The

1000M Full_Master

and

1000M Full_Slave

parameters refer to connections running

a 1000BASE-T cable for connection between the Switch port and other device capable

of a gigabit connection. The master

setting (

1000M Full_Master)

will allow the port to

advertise capabilities related to duplex, speed and physical layer type. The master

setting will also determine the master and slave relationship between the two connected

physical layers. This relationship is necessary for establishing the timing control between

the two physical layers. The timing control is set on a master

physical layer by a local

source. The slave

setting (

1000M Full_Slave)

uses loop timing, where the timing comes