Home » D-Link Manuals » Hubs & Switches » D-Link DWS-3160-24TC » Manual Viewer

D-Link DWS-3160-24TC DWS-3160 Series Web UI Reference Guide - Page 428

Short Guard Interval, Available MCS Indices

View all D-Link DWS-3160-24TC manuals

Add to My Manuals
Save this manual to your list of manuals

Page 428 highlights

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide equal to the RTS Threshold. Long Retries Display the maximum number of transmission attempts on frame sizes greater than the RTS Threshold. Transmit Lifetime (msecs) Display the number of milliseconds to wait before terminating attempts to transmit the MSDU after the initial transmission. Receive Lifetime (msecs) Display the number of milliseconds to wait before terminating attempts to reassemble the MMPDU or MSDU after the initial reception of a fragmented MMPDU or MSDU. Station Isolation Tick the check box to allow the AP blocking communication between wireless clients. Primary Channel Use the drop-down menu to set the Primary Channel as the Upper or Lower 20MHz channel in the 40-MHz band. This option only available when the Channel Bandwidth is configured as 40MHz. Short Guard Interval Select to enable or disable the short guard interval when operating in 802.11n mode. Multicast Tx Rate (Mbps) Select the 802.11 rate at which the radio transmits multicast frames. Supported Channels Display the channels supported for the radio mode. The available channels vary based on the selected Country Code in the Basic Setup Global window. Auto Eligible Tick the check boxes beneath each channel to include the channel in the automatic channel assignment process. Available MCS Indices Tick the check boxes to add MCS Index when operating in 802.11n mode. Rate Sets (Mbps) Display the transmission rate sets. Basic Tick the check boxes to indicate the data rates that all stations associating with the AP must support. Supported Tick the check boxes to indicate rates that the access point supports. The AP automatically chooses the most efficient rate based on factors like error rates and distance of client stations from the AP. Click the Apply button to accept the changes made. Click the Clear button to discard the changes made and return to the default settings. After clicking the VAP tab under the Profile Name tab, the following page will appear: 423

Section	Page
Table of Contents	3
Intended Readers	6
Typographical Conventions	6
Notes, Notices and Cautions	6
Section 1 Web-based Switch Configuration	7
Chapter 1 Introduction	7
Chapter 2 Login to the Web Manager	7
Chapter 3 Web-based User Interface	8
Areas of the User Interface	8
Chapter 4 Web Pages	9
Section 2 LAN	11
Chapter 1 System Configuration	11
Device Information	11
System Information Settings	12
Port Configuration	12
PoE	16
Serial Port Settings	19
Warning Temperature Settings	19
System Log Configuration	20
Time Range Settings	23
Port Group Settings	24
Time Settings	24
User Accounts Settings	25
Command Logging Settings	26
Chapter 2 Management	27
ARP	27
Gratuitous ARP	28
IPv6 Neighbor Settings	30
IP Interface	31
Management Settings	35
Session Table	36
Single IP Management	37
SNMP Settings	46
Telnet Settings	55
Web Settings	55
Chapter 3 L2 Features	56
VLAN	56
QinQ	74
Spanning Tree	77
Link Aggregation	84
FDB	87
L2 Multicast Control	91
Multicast Filtering	113
ERPS Settings	118
LLDP	121
NLB FDB Settings	130
Chapter 4 L3 Features	131
IPv4 Static/Default Route Settings	131
IPv4 Route Table	132
IPv6 Static/Default Route Settings	132
IP Forwarding Table	133
VRRP	133
Chapter 5 QoS	138
802.1p Settings	139
Bandwidth Control	141
Traffic Control Settings	143
DSCP	145
HOL Blocking Prevention	147
Scheduling Settings	147
Chapter 6 ACL	150
ACL Configuration Wizard	150
Access Profile List	151
CPU Access Profile List	167
ACL Finder	181
ACL Flow Meter	181
Egress Access Profile List	184
Egress ACL Flow Meter	196
Chapter 7 Security	199
802.1X	199
RADIUS	211
IP-MAC-Port Binding (IMPB)	215
MAC-based Access Control (MAC)	220
Compound Authentication	223
Port Security	226
ARP Spoofing Prevention Settings	228
BPDU Attack Protection	229
Loopback Detection Settings	230
Traffic Segmentation Settings	231
NetBIOS Filtering Settings	232
DHCP Server Screening	233
Access Authentication Control	235
SSL Settings	243
SSH	245
Trusted Host Settings	249
Safeguard Engine Settings	249
Captive Portal (CP)	251
Chapter 8 Network Application	271
DHCP	271
SNTP	277
Flash File System Settings	279
Chapter 9 OAM	281
CFM	281
Ethernet OAM	291
Cable Diagnostics	295
Chapter 10 Monitoring	297
Utilization	297
Statistics	298
Received (RX)	299
UMB_Cast (RX)	300
Transmitted (TX)	302
Received (RX)	303
Transmitted (TX)	305
Mirror	308
sFlow	310
Ping Test	313
Trace Route	314
Peripheral	315
Chapter 11 Save and Tools	316
Section 3 WLAN	317
Chapter 1 Security	317
Captive Portal (CP)	317
Chapter 2 Monitoring	336
Global	336
Peer Switch	344
Access Point	347
Client	368
QoS	387
Chapter 3 Administration	395
Basic Setup	395
AP Management	407
Advanced Configuration	416
Chapter 4 QoS	443
Access Control Lists	443
Differentiated Services	456
Chapter 5 Network Visualization	462
Download Image	462
Launch…	462
Section 4 Save and Tools	465
Chapter 1 Save	465
Save Configuration / Log	465
Chapter 2 Tools	466
License Management	466
Download Firmware	466
Upload Firmware	467
Download Configuration	467
Upload Configuration	468
Upload Log File	469
Reset	470
Reboot System	471
Appendices	473
Appendix A Mitigating ARP Spoofing Attacks Using Packet Content ACL	473
Appendix B Password Recovery Procedure	479
Appendix C System Log Entries	480
Appendix D Trap Log Entries	491
Appendix E RADIUS Attributes Assignment	495

Match case Limit results 1 per page

DWS-3160 Series Gigabit Ethernet Unified Switch Web UI Reference Guide

423

equal to the RTS Threshold.

Long Retries

Display the maximum number of transmission attempts on frame sizes greater than

the RTS Threshold.

Transmit Lifetime

(msecs)

Display the number of milliseconds to wait before terminating attempts to transmit

the MSDU after the initial transmission.

Receive Lifetime

(msecs)

Display the number of milliseconds to wait before terminating attempts to

reassemble the MMPDU or MSDU after the initial reception of a fragmented

MMPDU or MSDU.

Station Isolation

Tick the check box to allow the AP blocking communication between wireless

clients.

Primary Channel

Use the drop-down menu to set the Primary Channel as the

Upper

Lower

20-

MHz channel in the 40-MHz band. This option only available when the

Channel

Bandwidth

is configured as

40MHz

Short Guard Interval

Select to enable or disable the short guard interval when operating in 802.11n

mode.

Multicast Tx Rate

(Mbps)

Select the 802.11 rate at which the radio transmits multicast frames.

Supported Channels

Display the channels supported for the radio mode. The available channels vary

based on the selected Country Code in the Basic Setup Global window.

Auto Eligible

Tick the check boxes beneath each channel to include the channel in the automatic

channel assignment process.

Available MCS Indices

Tick the check boxes to add MCS Index when operating in 802.11n mode.

Rate Sets (Mbps)

Display the transmission rate sets.

Basic

Tick the check boxes to indicate the data rates that all stations associating with the

AP must support.

Supported

Tick the check boxes to indicate rates that the access point supports. The AP

automatically chooses the most efficient rate based on factors like error rates and

distance of client stations from the AP.

Click the

Apply

button to accept the changes made.

Click the

Clear

button to discard the changes made and return to the default settings.

After clicking the

VAP

tab under the Profile Name tab, the following page will appear: