Dell 2330d Service Manual - Page 77

EP setup

Get Dell 2330d - Laser Printer B/W PDF manuals and user guides
UPC - 884116003618
View all Dell 2330d manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Service Tag (only on some printers) The service tag number can only be viewed and cannot be changed. 1. Select Service Tag from the PRINTER SETUP menu. 2. Press Back to return to PRINTER SETUP. Engine Setting 1 through 4 Warning: Do not change these settings unless requested to do so by your next level of support. Model Name The serial number can only be viewed and cannot be changed. Configuration ID The configuration ID is used to communicate characteristics of certain areas of the printer that cannot be determined by hardware sensors. The configuration ID was originally set when the printer was manufactured and is located on the printer label. Edge to Edge When Edge to Edge is set to On, text and graphics are printed with all margins set to the physical edges of the page. This feature does not work in PPDS emulation. Par S Strobe Adj (parallel strobe adjustment) This setting adjusts the factory setting for the amount of time the strobe is sampled to determine that valid data is available on the parallel port. Incrementing this value by one means the strobe is sampled 50 nanoseconds longer. The range of values are between -4 and +6, in increments of one. A value of zero indicates no change is made from the factory setting. EP setup EP Setup displays the following selections: • EP Defaults • Fuser Temperature (Fuser Temp) • Transfer • Print Contrast • Gap Adjust • Automatic Darkness Adjustment (Auto Dark Adj) EP Defaults Restores all EP settings to factory default values. Selections are Restore and Do Not Restore. Fuser Temperature (Fuser Temp) Changing this setting can reduce media curl or melting of some letterhead images. Selections are Normal (default), Lower, and Lowest. Transfer The transfer can be adjusted to Low, Medium, or High. The default setting is Medium. Diagnostic aids 3-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
Diagnostic aids
3-13
Service Tag (only on some printers)
The service tag number can only be viewed and cannot be changed.
1.
Select
Service Tag
from the
PRINTER SETUP
menu.
2.
Press
Back
to return to
PRINTER SETUP
.
Engine Setting 1 through 4
Warning:
Do not change these settings unless requested to do so by your next level of support.
Model Name
The serial number can only be viewed and cannot be changed.
Configuration ID
The configuration ID is used to communicate characteristics of certain areas of the printer that cannot be
determined by hardware sensors. The configuration ID was originally set when the printer was manufactured
and is located on the printer label.
Edge to Edge
When Edge to Edge is set to
On
, text and graphics are printed with all margins set to the physical edges of the
page. This feature does not work in PPDS emulation.
Par S Strobe Adj (parallel strobe adjustment)
This setting adjusts the factory setting for the amount of time the strobe is sampled to determine that valid data
is available on the parallel port. Incrementing this value by one means the strobe is sampled 50 nanoseconds
longer. The range of values are between -4 and +6, in increments of one. A value of zero indicates no change is
made from the factory setting.
EP setup
EP Setup
displays the following selections:
•
EP Defaults
•
Fuser Temperature (Fuser Temp)
•
Transfer
•
Print Contrast
•
Gap Adjust
•
Automatic Darkness Adjustment (Auto Dark Adj)
EP Defaults
Restores all EP settings to factory default values. Selections are
Restore
and
Do Not Restore
.
Fuser Temperature (Fuser Temp)
Changing this setting can reduce media curl or melting of some letterhead images. Selections are
Normal
(default),
Lower
, and
Lowest
.
Transfer
The transfer can be adjusted to
Low
,
Medium
, or
High
. The default setting is Medium.