Dell Latitude CPt V Service Manual - Page 13

Orient the end of the interface cable with the ZIF connector, and insert

Get Dell Latitude CPt V PDF manuals and user guides View all Dell Latitude CPt V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

Some of the computer's interface connectors are zero insertion force (ZIF) connectors. These connectors are not removable, but they must be released to disconnect a cable from them (see Figure 4). movable part of connector (do not remove) To disconnect an interface cable from a ZIF connector, perform the following steps: 1. Insert a small flat-blade screwdriver behind the movable part of the connector. 2. Push gently sideways on the movable part of the connector until it releases the interface cable. 3. Grasp the interface cable and pull it out of the connector. To reconnect an interface cable to a ZIF connector, perform the following steps: 1. Use a small flat-blade screwdriver to open the movable part of the ZIF connector. 2. Orient the end of the interface cable with the ZIF connector, and insert the end of the cable into the connector. 3. While holding the cable in place, close the ZIF connector. To ensure a firm connection, make sure the ZIF connector is completely closed. support.dell.com Dell Latitude CPt V-Series/CPx H-Series Service Manual 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
support.dell.com
Dell Latitude CPt V-Series/CPx H-Series Service Manual
5
°ËºµÂ¾ÁÁ²À¼¾»¹
Some of the computer
’
s interface connectors are zero insertion force (ZIF)
connectors. These connectors are not removable, but they must be released
to disconnect a cable from them (see Figure 4).
±²³´µ¶·(¹··)²ÇλÀÀ¶Î¾²À³·ÁÀ·°À¾¶µ"Áζ·ºÁÈɶ
±²³´µ¶·¸³ÂÀ¸.´$¸½Å»»À½¿ÅÃÁ¸¾ÃÀ¸ÊþȺÆÀϸ³Å¸¾Íź¼¸¼¾Ç¾ÈÀ"¸¼Å¸»Å¿¸
¾ÄÄÆ˸¿ÅŸÇ̽¸ÄÃÀÁÁÌÃÀ¸¿Å¸¿ÂÀ¸ÇÅ;ÎÆÀ¸Ä¾Ã¿¸Åʸ¿ÂÀ¸½Å»»À½¿ÅÃÏ
To disconnect an interface cable from a ZIF connector, perform the following
steps:
1.
Insert a small flat-blade screwdriver behind the movable part of the
connector.
2.
Push gently sideways on the movable part of the connector until it releases
the interface cable.
3.
Grasp the interface cable and pull it out of the connector.
To reconnect an interface cable to a ZIF connector, perform the following
steps:
1.
Use a small flat-blade screwdriver to open the movable part of the ZIF
connector.
2.
Orient the end of the interface cable with the ZIF connector, and insert the
end of the cable into the connector.
3.
While holding the cable in place, close the ZIF connector.
To ensure a firm connection, make sure the ZIF connector is completely
closed.
movable part of
connector
(do not remove)