Dell OptiPlex 7071 Tower Tower Service Manual - Page 60

System board, Removing the system board

Page 60 highlights

Steps 1. Slide and place the intrusion switch in the chassis slot. 2. Connect the intruder cable to the system board. Next steps 1. Install the left-side cover. 2. Follow the procedure in After working inside your computer. System board Removing the system board Prerequisites 1. Follow the procedure in Before working inside your computer. NOTE: Your computer's Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup program after you replace the system board. NOTE: Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup program. You must make the appropriate changes again after you replace the system board. NOTE: Before disconnecting the cables from the system board, note the location of the connectors so that you can reconnect the cables correctly after you replace the system board. 2. Remove the left-side cover. 3. Remove the front cover. 4. Remove the memory modules. 5. Remove the wireless card. 6. Remove the solid-state drive/Intel Optane memory module. 7. Remove the graphics card. 8. Remove the coin-cell battery. 9. Remove the processor fan and heat-sink assembly. 60 Disassembly and reassembly

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96

Steps
1.
Slide and place the intrusion switch in the chassis slot.
2.
Connect the intruder cable to the system board.
Next steps
1.
Install the
left-side cover
.
2.
Follow the procedure in
After working inside your computer
.
System board
Removing the system board
Prerequisites
1.
Follow the procedure in
Before working inside your computer
.
NOTE:
Your computer’s Service Tag is stored in the system board. You must enter the Service Tag in the BIOS setup
program after you replace the system board.
NOTE:
Replacing the system board removes any changes that you have made to the BIOS using the BIOS setup
program. You must make the appropriate changes again after you replace the system board.
NOTE:
Before disconnecting the cables from the system board, note the location of the connectors so that you can
reconnect the cables correctly after you replace the system board.
2.
Remove the
left-side cover
.
3.
Remove the
front cover
.
4.
Remove the
memory modules
.
5.
Remove the
wireless card
.
6.
Remove the
solid-state drive/Intel Optane memory module
.
7.
Remove the
graphics card
.
8.
Remove the
coin-cell battery
.
9.
Remove the
processor fan and heat-sink assembly
.
60
Disassembly and reassembly