Dell PowerVault 51F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 111

Replacing a GBIC Module

Get Dell PowerVault 51F PDF manuals and user guides View all Dell PowerVault 51F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 111 highlights

Replacing a GBIC Module GBIC modules are installed and removed by inserting them into the system board from the front of the unit. Simple Network Management Protocol (SNMP) traps are generated upon GBIC insertion and removal. Removing a GBIC Module 1. Pull down the metal swing bar on the front of the GBIC and pull it out, as shown in Figure 6-2. 2. Carefully wiggle the GBIC from side to side to unseat it. swing bar Figure 6-2. GBIC Module If the module has squeeze prongs, squeeze the side prongs and carefully pull the GBIC out, as shown in Figure 6-3. squeeze prongs Figure 6-3. Squeeze Prongs on GBIC Module Installing a GBIC Module To install a GBIC module with squeeze prongs, insert the GBIC module into the port until its connector is firmly seated into the appropriate port. The latch prongs will lock and prevent the GBIC's accidental removal. NOTE: The GBIC module is keyed so it can be inserted in only one way. Do not force the insertion if the module does not slide in easily. support.dell.com Repair and Replacement 6-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
support.dell.com
Repair and Replacement
6-3
Replacing a GBIC Module
GBIC modules are installed and removed by inserting them into the system board
from the front of the unit. Simple Network Management Protocol (SNMP) traps are
generated upon GBIC insertion and removal.
Removing a GBIC Module
1.
Pull down the metal swing bar on the front of the GBIC and pull it out, as shown
in Figure 6-2.
2.
Carefully wiggle the GBIC from side to side to unseat it.
Figure 6-2.
GBIC Module
If the module has squeeze prongs, squeeze the side prongs and carefully pull the
GBIC out, as shown in Figure 6-3.
Figure 6-3.
Squeeze Prongs on GBIC Module
Installing a GBIC Module
To install a GBIC module with squeeze prongs, insert the GBIC module into the port
until its connector is firmly seated into the appropriate port. The latch prongs will lock
and prevent the GBIC’s accidental removal.
NOTE: The GBIC module is keyed so it can be inserted in only one way. Do not force
the insertion if the module does not slide in easily.
swing bar
squeeze prongs