Dell PowerVault 51F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 143

nbrStateShow, portDisable, ucastAllShow, LSDAllShow, <queue ID&gt, actTimersShow

Get Dell PowerVault 51F PDF manuals and user guides View all Dell PowerVault 51F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 143 highlights

Table A-1. Errors (continued) Module Error Severity Explanation NBFSM NGBRSTATE (2) An error occurred in the neighbor Finite State. UCAST ADDPATH (1) RELICPDB (2) SPFCOST(3) MQ QREAD (1) A static path configuration failed. The path selection task received an E_Port SCN, but the port was already ISL. An error occurred with computing the unicast path tree. A task was unable to receive a message. QWRITE (1) SYS NOMEM (1) SYSCALL (2) TIMERS ENQFAIL (1) A task was not able to post a message on a queue. The system's memory is exhausted. A system call into VxWorks failed. An error occurred while setting a timer. Action Check the neighbor's state with the nbrStateShow command. If the state is not NB_ST_FULL, force a state change with the portDisable command followed by portEnable. After a few seconds, if the state is not NB_ST_FULL, reboot both the local and remote switches. Check command parameters. Run the ucastAllShow command. Contact customer support. Run the LSDAllShow command. Contact customer support. Run the command show with the ID of the queue reported in the error. Contact customer support. See "MQ-QWRITE Error" found later in this chapter for more information. Reboot the switch. Contact customer support. Reboot the switch. Contact customer support. Reboot the switch. Run the commands actTimersShow and timerShow . Contact customer support. support.dell.com Error Messages A-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
support.dell.com
Error Messages
A-5
NBFSM
NGBRSTATE (2)
An error occurred
in the neighbor
Finite State.
Check the neighbor’s state
with the
nbrStateShow
command.
If the state is not
NB_ST_FULL, force a state
change with the
portDisable
command fol-
lowed by
portEnable
.
After a few seconds, if the
state is not NB_ST_FULL,
reboot both the local and
remote switches.
UCAST
ADDPATH (1)
A static path con-
figuration failed.
Check command
parameters.
RELICPDB (2)
The path selec-
tion task received
an E_Port SCN,
but the port was
already ISL.
Run the
ucastAllShow
command. Contact cus-
tomer support.
SPFCOST(3)
An error occurred
with computing
the unicast path
tree.
Run the
LSDAllShow
com-
mand. Contact customer
support.
MQ
QREAD (1)
A task was
unable to receive
a message.
Run the command
show
<queue ID>
with the ID of
the queue reported in the
error. Contact customer
support.
QWRITE (1)
A task was not
able to post a
message on a
queue.
See “MQ-QWRITE Error”
found later in this chapter for
more information.
SYS
NOMEM (1)
The system’s
memory is
exhausted.
Reboot the switch. Contact
customer support.
SYSCALL (2)
A system call into
VxWorks failed.
Reboot the switch. Contact
customer support.
TIMERS
ENQFAIL (1)
An error occurred
while setting a
timer.
Reboot the switch. Run the
commands
actTimersShow
and
timerShow <timer ID>
.
Contact customer support.
Table A-1.
Errors
(continued)
Module
Error
Severity
Explanation
Action