Dell PowerVault 51F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 113

Removing the Fan Assembly, Installing a New Fan Assembly,

Get Dell PowerVault 51F PDF manuals and user guides View all Dell PowerVault 51F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 113 highlights

Figure 6-5. Removing the Fan Assembly Removing the Fan Assembly 1. Disconnect the fan assembly's wiring harness from the center of the system board, as shown in Figure 6-5. Do not pull the connector wires. 2. Clear the metal tabs in front of the assembly by gently pushing the top of the tab toward the outside of the unit and the bottom to the inside. 3. After releasing the tabs, gently rotate the bottom of the assembly towards the front of the switch. 4. Pull the assembly up and back until you can slide it forward off the metal slats attached to the back of the chassis. Installing a New Fan Assembly 1. Tilt the assembly slightly up and slide it onto the two metal slats protruding from the back of the chassis. 2. Move aside the power supply wiring harnesses, lower the assembly onto the metal tabs protruding from the back of the power supply chassis. support.dell.com Repair and Replacement 6-5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
support.dell.com
Repair and Replacement
6-5
Figure 6-5.
Removing the Fan Assembly
Removing the Fan Assembly
1.
Disconnect the fan assembly’s wiring harness from the center of the system
board, as shown in Figure 6-5. Do not pull the connector wires.
2.
Clear the metal tabs in front of the assembly by gently pushing the top of the tab
toward the outside of the unit and the bottom to the inside.
3.
After releasing the tabs, gently rotate the bottom of the assembly towards the
front of the switch.
4.
Pull the assembly up and back until you can slide it forward off the metal slats
attached to the back of the chassis.
Installing a New Fan Assembly
1.
Tilt the assembly slightly up and slide it onto the two metal slats protruding from
the back of the chassis.
2.
Move aside the power supply wiring harnesses, lower the assembly onto the
metal tabs protruding from the back of the power supply chassis.