Dell PowerVault 51F Dell PowerVault 51F 8-Port Fibre Channel Switch Insta - Page 35

Preparing the Switch for Mounting, Removing the Rack Doors

Get Dell PowerVault 51F PDF manuals and user guides View all Dell PowerVault 51F manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

hinge release lever Figure 1-4. Removing the Rack Doors 3. Perform steps 1 and 2 to remove the back door from the rack. CAUTION: Store the two doors in an area where they will not fall over while you install the switch. Preparing the Switch for Mounting To prepare the switch for mounting, perform the following steps: 1. Place the manifold on a clean, flat surface. 2. Remove the foam spacer by gently pulling upward on the strap marked "Remove Before Use." 3. Be sure that no bits of foam remain in the manifold and that the gaskets were not damaged during extraction of the foam spacer. support.dell.com Installing the Dell PowerVault 51F Switch 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
support.dell.com
Installing the Dell PowerVault 51F Switch
1-7
Figure 1-4.
Removing the Rack Doors
3.
Perform steps 1 and 2 to remove the back door from the rack.
CAUTION: Store the two doors in an area where they will not fall over while
you install the switch.
Preparing the Switch for Mounting
To prepare the switch for mounting, perform the following steps:
1.
Place the manifold on a clean, flat surface.
2.
Remove the foam spacer by gently pulling upward on the strap marked “Remove
Before Use.”
3.
Be sure that no bits of foam remain in the manifold and that the gaskets were not
damaged during extraction of the foam spacer.
hinge
release
lever