Dell S4148F-ON Open Networking Hardware Diagnostic Guide June 2018 - Page 65

D3COLD WakeUp capability advertisement, Supported ports: [ TP ]

Get Dell S4148F-ON PDF manuals and user guides View all Dell S4148F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Output root@dellemc-diag-os:/etc/dn/diag# phytool --read-mac 34:17:eb:07:7c:00 root@dellemc-diag-os:/etc/dn/diag# phytool --eeprom-dump Offset Values ------ ------ 0x0000: 34 17 eb 07 7c 00 00 08 ff ff 05 10 ff ff ff ff 0x0010: 18 00 00 00 2f 40 41 1f 86 80 41 1f 86 80 80 ba 0x0020: ff ff ff ff 80 5c 47 00 00 00 40 00 00 4c ab 03 0x0030: 00 00 00 70 0e 1a 26 44 a3 07 42 1f 01 02 02 06 0x0040: 0c 00 47 21 00 00 ff ff ac 44 f6 00 44 1f 08 09 0x0050: 40 04 3c 00 00 00 04 14 00 00 00 00 00 10 ff ff 0x0060: 00 01 00 40 32 13 13 40 00 01 00 40 ff ff b0 03 0x0070: 00 01 00 40 00 01 00 40 d9 09 bc 03 ff ff b5 7e 0x0080: ff ff ff ff a5 0b 00 80 ff ff ff ff ff ff ff ff ..... root@dellemc-diag-os:/etc/dn/diag# phytool --reg-dump 0x00000: CTRL (Device control register) 0x08100241 Invert Loss-Of-Signal: no Receive flow control: enabled Transmit flow control: disabled VLAN mode: disabled Set link up: 1 D3COLD WakeUp capability advertisement: enabled Auto speed detect: disabled Speed select: 1000Mb/s Force speed: no Force duplex: no 0x00008: STATUS (Device status register) 0x00282383 Duplex: full Link up: link config Transmission: on DMA clock gating: disabled TBI mode: disabled Link speed: 1000Mb/s Bus type: PCI Express ... root@dellemc-diag-os:/etc/dn/diag# phytool --lb-test=100 TEST PASSED NOTE: The loopback test and set-intf will terminate the ethernet driver. You need to reboot to restart the driver cleanly. [1]+ Terminated setsid /bin/kni -c 0x3 -n 2 -- -p 1 --config="(0,0,1)" >> /dev/ null root@dellemc-diag-os:~# phytool --set-intf --speed=1000 [2]+ Done dhclient -q eth0 root@dellemc-diag-os done Port 0 Link Up - speed 1000 Mbps - full-duplex root@dellemc-diag-os:~# root@dellemc-diag-os:~# phytool --show-intf Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supported pause frame use: Symmetric Supports auto-negotiation: Yes Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Advertised pause frame use: No Dell EMC DAIG-OS tools 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Output
root@dellemc-diag-os:/etc/dn/diag# phytool --read-mac
34:17:eb:07:7c:00
root@dellemc-diag-os:/etc/dn/diag# phytool --eeprom-dump
Offset
Values
------
------
0x0000:
34 17 eb 07 7c 00 00 08 ff ff 05 10 ff ff ff ff
0x0010:
18 00 00 00 2f 40 41 1f 86 80 41 1f 86 80 80 ba
0x0020:
ff ff ff ff 80 5c 47 00 00 00 40 00 00 4c ab 03
0x0030:
00 00 00 70 0e 1a 26 44 a3 07 42 1f 01 02 02 06
0x0040:
0c 00 47 21 00 00 ff ff ac 44 f6 00 44 1f 08 09
0x0050:
40 04 3c 00 00 00 04 14 00 00 00 00 00 10 ff ff
0x0060:
00 01 00 40 32 13 13 40 00 01 00 40 ff ff b0 03
0x0070:
00 01 00 40 00 01 00 40 d9 09 bc 03 ff ff b5 7e
0x0080:
ff ff ff ff a5 0b 00 80 ff ff ff ff ff ff ff ff
.....
root@dellemc-diag-os:/etc/dn/diag# phytool --reg-dump
0x00000: CTRL (Device control register)
0x08100241
Invert Loss-Of-Signal:
no
Receive flow control:
enabled
Transmit flow control:
disabled
VLAN mode:
disabled
Set link up:
1
D3COLD WakeUp capability advertisement:
enabled
Auto speed detect:
disabled
Speed select:
1000Mb/s
Force speed:
no
Force duplex:
no
0x00008: STATUS (Device status register)
0x00282383
Duplex:
full
Link up:
link config
Transmission:
on
DMA clock gating:
disabled
TBI mode:
disabled
Link speed:
1000Mb/s
Bus type:
PCI Express
...
root@dellemc-diag-os:/etc/dn/diag# phytool --lb-test=100
TEST PASSED
NOTE: The loopback test and set-intf will terminate the ethernet driver.
You need to reboot to
restart the driver cleanly.
[1]+
Terminated
setsid /bin/kni -c 0x3 -n 2 -- -p 1 --config="(0,0,1)" >> /dev/
null
root@dellemc-diag-os:~# phytool --set-intf --speed=1000
[2]+
Done
dhclient -q eth0
root@dellemc-diag-os:~#
........................
done
Port 0 Link Up - speed 1000 Mbps - full-duplex
root@dellemc-diag-os:~# root@dellemc-diag-os:~# phytool --show-intf
Settings for eth0:
Supported ports: [ TP ]
Supported link modes:
10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supported pause frame use: Symmetric
Supports auto-negotiation: Yes
Advertised link modes:
10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised pause frame use: No
Dell EMC DAIG-OS tools
65