Dell S5212F-ON Open Networking Hardware Diagnostic Guide December 2021 - Page 53

Output, Read output, Write output, Test Status Fail Bits : offset 0x50 = 0x0

Get Dell S5212F-ON PDF manuals and user guides View all Dell S5212F-ON manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

-I, --iteration= Iteration command execution -R, --reg= Register -V, --val= Value to be set Output Read output root@dell-diag-os:~# nvramtool --read NVRAM Values: 0x00 0x9f 0x00 0xe6 0x03 0x03 0x00 0xea Test Status Fail Bits : offset 0x50 = 0x0 7 NVRAM test = 0 6 SSD test = 0 5 COLD/SMF Reg check = 0 4 PCI test = 0 3 Upper DRAM test = 0 2 Lower DRAM test = 0 1 ECC test = 0 0 SPD test = 0 Test Status Pass Bits : offset 0x51 = 0x9f 7 NVRAM test = 1 6 SSD test = 0 5 CPLD/SMF Reg check = 0 4 PCI test = 1 3 Upper DRAM test = 1 2 Lower DRAM test = 1 1 ECC test = 1 0 SPD test = 1 RMT Control : offset 0x52 = 0x0 7: 4 Undefined = 0 3 RMT Test Enable = 0 2: 0 RMT Test Reboot Count = 0 Status ID Byte : offset 0x53 = 0xe6 POST Control Bits : offset 0x54 = 0x3 7 Force Cold Boot = 0 6 POST Extended Upper DRAM test = 0 5 POST Extended Lower DRAM test = 0 4 POST Extended tests = 0 3 Reserved = 0 2 POST Verbose Mode = 0 1 POST Stop on Error = 1 0 POST Enable = 1 EDA Control Bits : offset 0x55 = 0x3 5: 4 EDA Verbose Level = 0 3 EDA Extended Tests = 0 2 EDA Verbose Mode = 0 1 EDA Stop on Error = 1 0 EDA Enable = 1 EDA Extra Bits : offset 0x56 = 0x0 Control ID Byte : offset 0x57 = 0xea root@dell-diag-os:~# Write output ./nvramtool --write --reg=0x54 --val=0x1 Dell EMC DAIG-OS tools 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
-I, --iteration=
Iteration command execution
-R, --reg=
Register
-V, --val=
Value to be set
Output
Read output
root@dell-diag-os:~# nvramtool --read
NVRAM Values:
0x00 0x9f 0x00 0xe6 0x03 0x03 0x00 0xea
Test Status Fail Bits : offset 0x50 = 0x0
7 NVRAM test = 0
6 SSD test = 0
5 COLD/SMF Reg check = 0
4 PCI test = 0
3 Upper DRAM test = 0
2 Lower DRAM test = 0
1 ECC test = 0
0 SPD test = 0
Test Status Pass Bits : offset 0x51 = 0x9f
7 NVRAM test = 1
6 SSD test = 0
5 CPLD/SMF Reg check = 0
4 PCI test = 1
3 Upper DRAM test = 1
2 Lower DRAM test = 1
1 ECC test = 1
0 SPD test = 1
RMT Control : offset 0x52 = 0x0
7: 4 Undefined = 0
3 RMT Test Enable = 0
2: 0 RMT Test Reboot Count = 0
Status ID Byte : offset 0x53 = 0xe6
POST Control Bits : offset 0x54 = 0x3
7 Force Cold Boot = 0
6 POST Extended Upper DRAM test = 0
5 POST Extended Lower DRAM test = 0
4 POST Extended tests = 0
3 Reserved = 0
2 POST Verbose Mode = 0
1 POST Stop on Error = 1
0 POST Enable = 1
EDA Control Bits : offset 0x55 = 0x3
5: 4 EDA Verbose Level = 0
3 EDA Extended Tests = 0
2 EDA Verbose Mode = 0
1 EDA Stop on Error = 1
0 EDA Enable = 1
EDA Extra Bits : offset 0x56 = 0x0
Control ID Byte : offset 0x57 = 0xea
root@dell-diag-os:~#
Write output
./nvramtool --write --reg=0x54 --val=0x1
Dell EMC DAIG-OS tools
53