Dell Vostro 5590 Service Manual - Page 47

Installing the system board

Get Dell Vostro 5590 PDF manuals and user guides View all Dell Vostro 5590 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Steps 1. Locate the system board on your computer. 2. Lift the latch and disconnect the input and output board cable from the connector on the system board. 3. Lift the latch and disconnect the power button cable from the connector on the system board. 4. Peel the adhesive tape above the display cable connector. 5. Lift the latch and disconnect the display cable from the connector on the system board. 6. Remove the WLAN antenna cables. 7. Disconnect the coin-cell battery cable and the speaker cable from the connectors on the system board. 8. Lift the latch and disconnect the hard drive cable, touchpad cable, keyboard backlit cable and the keyboard cable from the connectors on the system board. 9. Remove the five (M2x4) and two (M2x5) screws that secure the system board to the plamrest assembly. 10. Lift the system board off the palmrest and keyboard assembly. Installing the system board Prerequisites If you are replacing a component, remove the existing component before performing the installation procedure. About this task The figure indicates the location of the system board and provides a visual representation of the installation procedure. Removing and installing components 47

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
Steps
1.
Locate the system board on your computer.
2.
Lift the latch and disconnect the input and output board cable from the connector on the system board.
3.
Lift the latch and disconnect the power button cable from the connector on the system board.
4.
Peel the adhesive tape above the display cable connector.
5.
Lift the latch and disconnect the display cable from the connector on the system board.
6.
Remove the WLAN antenna cables.
7.
Disconnect the coin-cell battery cable and the speaker cable from the connectors on the system board.
8.
Lift the latch and disconnect the hard drive cable, touchpad cable, keyboard backlit cable and the keyboard cable from the connectors
on the system board.
9.
Remove the five (M2x4) and two (M2x5) screws that secure the system board to the plamrest assembly.
10.
Lift the system board off the palmrest and keyboard assembly.
Installing the system board
Prerequisites
If you are replacing a component, remove the existing component before performing the installation procedure.
About this task
The figure indicates the location of the system board and provides a visual representation of the installation procedure.
Removing and installing components
47