Denon AVR 3802 Owners Manual - Page 17

Operating DENON audio components 1 Use the mode selector buttons to select the component you want to operate. The mode switches between "AMP", "TUNER" and "MULTI" each time the RECEIVER button is pressed, between "CDR", "MD" and "TAPE" each time the CDR/MD/TAPE button is pressed, between "DBS" and "CABLE" each time the DBS/CABLE button is pressed, and between "DVD" and "DVD SETUP" each time the DVD button is pressed, and between "VCR" and "VCR2" eachtime the VCR button is pressed. 2 Operate the audio component. • For details, refer to the component's operating instructions. It may not be possible to operate some models. POWER OFF ON / SOURCE RC-884 REMOTE CONTROL UNIT 1 TV CD CDR/MD/ TAPE RECEIVER VCR DBS/CABLE VDP DVD DISPLAY SURR. PARA. SETUP TUNING MENU OSD RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING TUNER 1 PHONO 2 CDR/ TAPE VDP 4 5 VCR-1 7 VCR-2 / V.AUX 8 - CD 3 DVD 6 TV/DBS 9 TV/ VCR RDS 0 +10 PTY RT 1. CD player (CD) system buttons SETUP TUNING RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING TUNER 1 PHONO 2 CDR/ TAPE VDP 4 5 VCR-1 VCR-2 /V.AUX 7 8 - CD 3 DVD 6 TV/DBS 9 TV/ VCR 0 +10 6, 7 2 1 8, 9 3 SKIP +, - 0~9, +10 : Manual search (forward and reverse) : Stop : Play : Auto search (to beginning of track) : Pause : (for CD changers only) : 10 key 3. MD recorder (MD), CD recorder (CDR) system buttons SETUP TUNING RETURN A/B MEMORY BAND CHANNEL MODE VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING TUNER 1 PHONO 2 CDR/ TAPE VDP 4 5 VCR-1 VCR-2 /V.AUX 7 8 - CD 3 DVD 6 TV/DBS 9 TV/ VCR 0 +10 6, 7 2 1 8, 9 3 0~9, +10 : Manual search (forward and reverse) : Stop : Play : Auto search (to beginning of track) : Pause : 10 key 2. Tape deck (TAPE) system buttons SETUP TUNING RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING - TUNER PHONO CD 1 2 3 C/ 6 7 2 1 3 8 A/B : Rewind : Fast forward : Stop : Forward play : Pause : Reverse play : Switch between sides A and B 4. Tuner system buttons TUNING D, H BAND MODE MEMORY SHIFT CHANNEL +, - 1~8 RDS PTY RT SETUP TUNING RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING TUNER 1 PHONO 2 CDR/ TAPE VDP 4 5 VCR-1 VCR-2 / V.AUX 7 8 - CD 3 DVD 6 TV/DBS 9 TV/ VCR RDS TEST TONE 0 PTY SPEAKER +10 RT OUTPUT : Tuning up/down : Switch between AM and FM bands : Switch between AUTO and MONO : Preset memory : Switch preset channel range : Preset channel up/down : 10 key : RDS search : PTY search : Radio Text ENGLISH Preset memory By using the preset memory, the included remote control unit can be used to control other makes of video equipment. Note that this is not possible for some models, however. In such cases, use the learning function (see page 19) to store the remote control signals in the remote control unit's memory. See page 20 for instructions on resetting the data stored in the preset memory. 1 Press the power ON/SOURCE button and the OFF button at the same time. • "SET UP" appears on the remote control unit's display. OFF ON / SOURCE 2 ENTER SHIFT Press the ENTER button. 3 Use the D and H cursor buttons to display "ENTER CODE" on the remote control unit, then press the ENTER button. The remote control unit's display switches as follows each time the D and H cursor buttons are pressed. ENTER CODE CODE NO LEARN TUNING BAND MODE TUNING SYS CALL ENTER RESET SHIFT AUTO SEARCH 1 POWER OFF ON / SOURCE RC-884 REMOTE CONTROL UNIT 3, 4 2, 3, 4 5 TV CD CDR/MD/ TAPE RECEIVER VCR DBS/CABLE VDP DVD DISPLAY SURR. PARA. SETUP TUNING MENU OSD RETURN A/B MEMORY BAND MODE CHANNEL VOLUME TUNING + + SKIP ENTER - SKIP SHIFT MUTING TUNER 1 PHONO 2 CDR/ TAPE VDP 4 5 VCR-1 7 VCR-2 / V.AUX 8 - CD 3 DVD 6 TV/DBS 9 TV/ VCR RDS TEST TONE DOLBY/DTS SURROUND 0 PTY SPEAKER +10 RT OUTPUT SURROUND DSP SIMU. 5CH / 7CH STEREO 6.1 / 7.1 SURROUND DIRECT STEREO MODE INPUT ANALOG EXT.IN SYSTEM CALL CALL 1 CALL 2 BACKLIGHT 4 5 After "SEL MODE" is displayed, the last selected mode is set. Use the D and H cursor buttons to display the component whose codes you want to store in the memory, then press the ENTER button. TUNING BAND MODE TUNING ENTER SHIFT 1 2 3 Referring to the included List of Preset Codes, use the 4 5 6 number buttons to input the 7 8 9 preset code (a 4-digit number) for the manufacturer 0 of the component whose signals you want to store in the memory. The display switches as shown below each 6 "OK" is displayed when the signals are registered and the mode is terminated. time the D and H cursor buttons are pressed. TV CD MD TAPE VCR 7 To store the codes of another component in the memory, repeat steps 1 to 6. DVD VDP CABLE DBS VCR2 NOTES: • The signals for the pressed buttons are emitted while setting the preset memory. To avoid accidental operation, cover the remote control unit's transmitting window while setting the preset memory. • Depending on the model and year of manufacture, this function cannot be used for some models, even if they are of makes listed on the included list of preset codes. • Some manufacturers use more than one type of remote control code. Refer to the included list of preset codes to change the number and check. 17