Denon AVR4810CI Owners Manual - English - Page 116

Learning Function

Get Denon AVR4810CI - 9.3 Channel Multi-Zone Home Theater Receiver PDF manuals and user guides
UPC - 883795001151
View all Denon AVR4810CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Getting Started Connections Settings Playback Multi-zone Remote Control Information Troubleshooting Specifications Learning Function If your AV devices are of a brand other than DENON or if they cannot be operated with the preset memory function, their remote control signals can be transfered to stored in the AVR-4810CI's main remote control unit. 1 Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice. 2 Press [9], [7] and [5], in that order. The signal transmission indicator flashes twice and the learning mode is set. 3 Press [DEVICE SELECTOR] for the device you want to set 4 Press the button to be set. The main remote control unit's display turns off. b If a button that cannot be learned is pressed, the signal transmission indicator lights but the signal is not learned. 5 Point the main remote control units directly at each other and press and hold the button on the other device's remote control unit that you want to learn. Once learning is completed normally, the display lights and the signal transmission indicator flashes twice. • With some remote control units, the signals cannot be learned or the device will not operate properly even when the signals have been learned. In this case, use the device's own remote control unit. • Learned buttons have priority over the preset memory. If you no longer need the learned setting, reset the learning function (vpage 116). NOTE • [POWER ON], [POWER OFF] and [SOURCE SELECT] cannot be learned. • Do not learn any remote control signals at [RC SETUP]. • The MAIN, ZONE2, ZONE3, ZONE4 and MACRO modes cannot be learned. • Codes cannot be learned at [MASTER VOLUME] or [MUTE] when the main remote control unit is set to "TUNER", "SAT TU", "DTU", "NET/USB" or "iPod". Operating the Main Remote Control Unit b If you want to learn other buttons, repeat steps 4 and 5. b The mode can be switched by pressing [DEVICE SELECTOR]. b The signal transmission indicator lights once for a long time if learning was not possible 6 Press and hold in [RC SETUP] for at least 3 seconds. The signal transmission indicator flashes twice and the setting is completed. 113

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
±±³
Getting Started
Connections
Settings
Playback
Remote Control
Multi-zone
Information
Troubleshooting
Specifications
Remote Control
Operating the Main Remote Control Unit
If your AV devices are of a brand other than DENON or if they cannot
be operated with the preset memory function, their remote control
signals can be transfered to stored in the AVR-4810CI’s main remote
control unit.
Learning Function
1
Press and hold in
[RC SETUP]
for at least 3 seconds.
The signal transmission indicator flashes twice.
2
Press
[9]
,
[7]
and
[5]
, in that order.
The signal transmission indicator flashes twice and the learning
mode is set.
3
Press
[DEVICE SELECTOR]
for the device you want
to set
4
Press the button to be set.
The main remote control unit’s display turns off.
If a button that cannot be learned is pressed, the signal transmission
indicator lights but the signal is not learned.
b
5
Point the main remote control units directly at each
other and press and hold the button on the other
device’s remote control unit that you want to learn.
Once learning is completed normally, the display lights and the
signal transmission indicator flashes twice.
If you want to learn other buttons, repeat steps 4 and 5.
The mode can be switched by pressing
[DEVICE SELECTOR]
.
The signal transmission indicator lights once for a long time if
learning was not possible
b
b
b
6
Press and hold in
[RC SETUP]
for at least 3 seconds.
The signal transmission indicator flashes twice and the setting
is completed.
With some remote control units, the signals cannot be learned or the
device will not operate properly even when the signals have been
learned. In this case, use the device’s own remote control unit.
Learned buttons have priority over the preset memory. If you no
longer need the learned setting, reset the learning function (
v
page
116).
•
•
NOTE
[POWER ON]
,
[POWER OFF]
and
[SOURCE SELECT]
cannot be
learned.
Do not learn any remote control signals at
[RC SETUP]
.
The MAIN, ZONE2, ZONE3, ZONE4 and MACRO modes cannot be
learned.
Codes cannot be learned at
[MASTER VOLUME]
or
[MUTE]
when
the main remote control unit is set to “TUNER”, “SAT TU”, “DTU”,
“NET/USB” or “iPod”.
•
•
•
•