Denon AVR4810CI Owners Manual - English - Page 45

Getting Started Connections Settings Playback Multi-zone Remote Control Information Troubleshooting Specifications Making Detailed Settings (Manual Setup) Setting items Speaker Configuration (Continued) Setting contents Front Height : Set the presence and size of the front height speakers. • Large : Use of a large speaker that can adequately playback low frequencies. • Small : Use of a small speaker that has inadequate playback capacity for low frequencies. • None : Select when the front height speakers are not connected. When "Configuration" is set to "5.1ch" in the "Amp Assign" settings (vpage 41) or when "FH" is not selected using "Extra Channel", no settings can be made for "Front Height". Front Wide : Set the presence and size of the front wide speakers. • Large : Use of a large speaker that can adequately playback low frequencies. • Small : Use of a small speaker that has inadequate playback capacity for low frequencies. • None : Select when the front wide speakers are not connected. When "Configuration" is set to "5.1ch" in the "Amp Assign" settings (vpage 41) or when "FW" is not selected using "Extra Channel", no settings can be made for "Front Wide". Bass Setting Subwoofer Mode : Select low range signals to be reproduced by Settings for subwoofer and subwoofer. LFE signal range playback. • LFE : The low range signal of the channel set to "Small" speaker size is added to the LFE signal output from the subwoofer. • LFE+Main : The low range signal of all channels is added to the LFE signal output from the subwoofer. • This can be set when "Speaker Configuration" - "Subwoofer" (vpage 41) is set to "Yes". • Play music or a movie source and select the mode offering the strongest bass. • Select "LFE+Main" if you want the bass signals to always be produced from the subwoofer. LPF for LFE : Set LFE signal playback range. • 80Hz / 90Hz / 100Hz / 110Hz / 120Hz / 150Hz / 200Hz / 250Hz Setting items Setting contents Distance Feet / Meters : Set the unit of distance. Set distance from listening Step : Set the minimum variable width of the distance. position to speakers. • 1ft / 0.1ft Measure beforehand the • 0.1m / 0.01m distance from the listening Default : Reset all distance settings to factory default. position to each speaker. • Yes : Reset to the defaults. • No : Do not reset to the defaults. When you select "Default" and press ENTER, the "Return all settings to the default?" prompt is displayed. Select either "Yes" or "No", and press ENTER. Front L / Front R / Center / Subwoofer / Surround A L / Surround A R / Surround B L / Surround B R / Surr. Back Lz / Surr. Back Rz / Front Height L / Front Height R / Front Wide L / Front Wide R : Select the speaker. z: W hen the "Speaker Configuration" - "Surround Back" setting (vpage 41) is set to "1spkr", "Surr. Back" is displayed. • 0.0ft ~ 60.0ft / 0.00m ~ 18.00m : Set the distance. • Speakers set to "None" in "Speaker Configuration" (vpage 41) are not displayed. • The speakers that can be selected differ depending on the "Amp Assign" (vpage 41) and "Speaker Configuration" (vpage 41) settings. • Default settings : Front / Center / Subwoofer / Front Height / Front Wide : 12.0 ft (3.60 m) Surround A / Surround B / Surround Back : 10.0 ft (3.00 m) • Set the difference in the distance between the speakers to less than 20 feet (6.0 meters). Channel Level Test Tone : Output test tone. Set the volume of the test • Front L / Front Height L / Center / Front Height R / Front R / Front tone to be the same when it Wide R / Surround R /Surr. Back Rz /Surr. Back Lz / Surround L / is output from each speaker. Front Wide L / Subwoofer : Select the speaker. z : W hen the "Speaker Configuration" - "Surround Back" setting (vpage 41) is set to "1spkr", "Surr. Back" is displayed. • -12dB ~ +12dB (0dB) : Adjust the volume. • Speakers set to "None" in the "Speaker Configuration" (vpage 41) settings are not displayed. • When o is pressed while the subwoofer volume is set to "-12 dB", the "Subwoofer" setting switches to "OFF". • When a headphones jack is inserted in the PHONES terminal of the AVR4810CI, the "Channel Level" is not displayed. • You can also press CHANNEL LEVEL to set (vpage 100 "Adjust the Volume of the Different Speakers"). 42 Main remote control unit operation buttons :Displaying the menu Cancel the menu :Moves the cursor (Up/Down/Left/Right) :Confirm the setting :Return to previous menu