Denon DND6000 Operating Instructions - Page 8
Part Names And Functions - dn d6000 manual
UPC - 081757506366
View all Denon DND6000 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 8 highlights
ENGLISH 3 PART NAMES AND FUNCTIONS (1) Front panel (2) Rear panel q POWER button (¢ON £OFF) • Push this button to turn power on and off. CAUTION: • Do not turn off the power while a disc is loading or being ejected. Otherwise loading mechanism may be damaged. w POWER indicator • This lights when the power is on. e Disc loading slot • Load the disc slowly, and release it once the DN-D6000 starts grabbing the disc in. NOTE: Please clean the dirt of the label side of a disc and start loading of the disc. The dirt causes a slip of a disc loader roller. y Analog output jacks (LINE OUT) • This is unbalanced RCA output jacks. • Audio signals outputs. u Fader start jack • Use this when your mixer has Fader Start function with 3.5 mm stereo mini cord. i Digital output jack • Digital data is available from this jack. • Use 75 Ω/ohms pin cord for connection. • We recommend you use braided wire type shielded cable. NOTE: The playback level after analog conversion is set to -12dB bellow the usual level to avoid digital distortion. o Remote connector (REMOTE) • Connect this connector to the RC-D60 using the included cord. CAUTIONS: • Do not load discs when the power is turned off. • Do not try to forcibly remove a disc once the DN-D6000 has started to grab the disc. • Do not load more than once disc at a time or insert anything other than discs. Otherwise loading mechanism may be damaged. r Disc slot LED • This flashes while the disc is ejecting. • The LED lights when the disc is not loaded and serves as the disc slot illumination. t DISC EJECT button • Push this button to eject the disc. • The disc will not eject during playback. Stop playback before pushing this button. (3) RC-D60 Front panel CAUTION: • Note that there are many buttons working two different function selected by short time pushing or long pushing (1second or more). The mark indicates short time push function and mark indicates long time push function. !0 PLAY/PAUSE button (13) • This button will start or pause playback. • Push once to start playback, once again to pause playback, and once more to resume playback. !1 CUE button • Pushing this button in play mode will force the track back to the position which playback started. While in search mode, it makes new Cue point. (Cue) • In Cue mode, by pushing the CUE button makes a Stutter sound from the Cue point. This is called Stutter play. (Stutter) !2 Scratch Disc Use this vinyl scratch disc for scan, manual search, Pitch Bend and Scratch operations. !3 FLIP/CLR button • FLIP: Use this to select operating mode of A1 and A2 buttons, from Hot Start mode and Stutter mode. The display will indicate "H/S" or "STR" • A1, A2 CLR: If the A1 or A2 button is pushed while pushing the FLIP button, you can clear the selected A point. By holding down just the FLIP button for more than 1 sec, you can clear A1 and A2 points all at once. !4 (SAMP) RVS/CLR button • (SAMP)RVS: Use this to select the sample play direction forward and reverse. When select reverse RVS LED lights up. • (SAMP) CLR: If the SAMP button is pushed while pushing the this button, you can clear the SAMP data. Or, by holding down just the this button for more than 1 sec. !5 A1, A2 button • Using this button you can create starting point for Hot Start, Seamless Loop and Stutter. !6 SAMP button • Push this button to record or play sound of Sampler. !7 B button • Use this to set the B point for to create a Seamless Loop after the A point has been set. !8 (SAMP) B button • Use this to set the Sampler loop B point. !9 EXIT/RELOOP button • Use this to exit or return back again to Seamless loop playback. You can add variety to looping with this function. @0 (SAMP)EXIT/RELOOP • Use this to turn the Sampler Loop mode on and off. Also acts as EXIT/RELOOP button for Sampler Loop to exit or back again. @1 NEXT TR./B TRIM button • When the button is pressed during playback, the NEXT TRACK MODE is selected. If the button is pressed again, the B TRIM MODE is selected. In the standby and pause modes, only the B TRIM MODE can be selected. @2 (SAMP.) STOP button • Push this button while in Sampler record or playback, Sampler record or playback stops. @3 TITLE button • CD TEXT: When there is CD text data, the CD text data is displayed automatically or when the button is pressed. If no TEXT is available, the display will indicate "No TEXT". • MP3: When an MP3 file has ID-3 tag data, the title, artist name and album name are selected and displayed each time the button is pressed. 8