Denon DND6000 Operating Instructions - Page 9

ENGLISH @4 TIME,/ CONT./SINGLE button • TIME: A short push will displays mode changes between ELAPSED TIME and REMAIN TIME. • 4-way TOTAL TIME display mode can be selected by ⁄5 PRESET "(13) Time Mode". • At this time, you can select display mode from four modes, TRACK ELAPSED, TRACK REMAIN, DISC ELAPSED and DISC REMAIN. • CONT./SINGLE: Long pushing play ending mode between CONT (continue: play more tracks) and SINGLE (stop playing and ReCUE's back to your set point). • SINGLE PLAY LOCK: When SINGLE PLAY LOCK is selected, track selection during playback is disabled. This prevents playback from stopping when the Track Select Knob is turned accidentally during playback.Play ending mode is the same as single mode. @5 MEMO, PRESET button • MEMO: The memo mode starts when this button is pushed once in the Cue mode. • PRESET: When this button is pushed for more than 1 sec, the PRESET mode menu is displayed. The machine status must be in, CUE, PAUSE or No Disc mode before entering the preset mode. @6 (SAMP) PITCH/VOL. button • When the button is pressed, the SAMPLER PITCH is selected. When pressed again, the SAMPLER LEVEL is selected. Pitch of Sampler and output level of Sampler playback can be adjusted with the PARAMETERS knob. @7 DISC MODE button Select from Scratch playback, Bend mode or Manual Frame Search mode. • SCRATCH: This button lights up or blinks in orange or green when scratching. Manipulate the sound by pushing down on the disc. • BEND/SEARCH: When the Disc mode is set to BEND during playback, it alternates as the pitch bend function. The display will indicate "Bend". When Disc mode is set to Search, during Pause or CUE mode, it alternates as the Manual Search and Fast search function. It works as the Manual search when the disk is turned. It works as the Scan when the disk is pushed. The display will indicate "Search". @8 FILTER • One of three filters (LOW PASS, MID PASS and HIGH PASS) can be selected. @9 FLANGER • The feedback time and feedback gain can be selected. #0 TAP, LOCK, AUTO/INPUT BPM button • TAP: When you push this button repeatedly, the Auto mode turns off and starts measuring your Beats Per Minute (BPM) by tapping. • LOCK: When this button is pressed once while the auto BPM counter is operating, the data measured by the auto BPM counter is locked. • AUTO: When pushing the TAP button for 1 second, activates AUTO BPM mode. The measured BPM is displayed in the character section of the display. • INPUT BPM : When the TAP button is pressed and held in for more than 2 seconds, the BPM input mode is set and the BPM value can be input directly with the PARAMETERS knob. When the tap button is pressed again, the BPM input mode is turned off. NOTE: If you select a new track, AUTO BPM mode turns on automatically. #1 ECHO/LOOP • The ECHO and LOOP functions can be selected. The feedback time and feedback number can be selected. Looping for the feedback time (ECHO LOOP) is possible by setting the feedback number to "MAX". #2 TRACK/PARAMETERS knob • TRACK: When PARAMETERS LED is on, turn this knob to select tracks. By pushing this knob down while turning, the tracks will change by 10 tracks at a time. • PARAMETERS: When the PARAMETER LED is flashing, turn this knob to select and change the parameter for items found in the Platter effects, Memo, and Preset data, etc. • FILE SEARCH MODE:MP3 DISC only. When pushing this knob for more than 1 second, the file search selection mode is selected. #3 FAST SEARCH (6), Quick Jump button #4 FAST SEARCH (7) Quick Jump button • Quick Jump: When one of these buttons is tapped shortly, the playback position jumps approximately 10 seconds in the reverse (6) or forward (7) direction. The jump time can be changed in the preset mode. • FAST SEARCH: When one of these buttons is pressed and held in, the disc is fast-searched in the reverse (6) or forward (7) direction. #5 PITCH BEND - button #6 PITCH BEND + button • Pushing these buttons will change main playing speed temporarily. • While pushing PITCH BEND + button the playing speed increases and speed decreases while pushing PITCH BEND - button. • When release button, playing speed returns to the previous speed. #7 Pitch Slider • Use this slider to adjust playing speed. • The playing speed decreases when slid upwards and increases downwards. #8 PITCH/KEY, RANGE button • With this button you can select PITCH and KEY ADJUST mode. Mode changes Pitch on, Key Adjust on and both off cyclically. PITCH LED indicates in Pitch mode and KEY ADJUST indicator in the display lights up in Key Adjust mode. • RANGE: Push this button for more than 1 sec to select the pitch range. The pitch range can be selected with the PARAMETERS knob from ±4, 10, 16, 24, 50 or 100%. #9 RVS button, DRAG-S button • Push this button to set the RVS mode. • Push this button for more than 1sec to set the DRAG-S. $0 BRAKE button • Push this button to set the BRAKE. (4) RC-D60 Rear panel $1 REMOTE connector • Connect this connector to the REMOTE connector on the DN-D6000 using the included cord. 9