Home » Epson Manuals » Print Servers » Epson C32C824151 » Manual Viewer

Epson C32C824151 Technical Reference - Page 79

Initializing, Version Upgrading

UPC - 000054074415

Add to My Manuals
Save this manual to your list of manuals

Page 79 highlights

UB-E02 Technical Reference Guide 5.5.6 Initializing To initialize the UB-E02 when the power is turned on or reset, the standby period is required for 10 seconds. During this period. All network functions do not work. The waiting time is: When the IP address setting is Manual (Fixed): When the IP address setting is Auto: approximately 6 seconds approximately 13 seconds (It can be longer, depending on the reply time of the host.) 5.5.7 Version Upgrading The module can upgrade its own firmware over the network. 5.5.7.1 Supported protocol ❏ TFTP 5.5.7.2 Upgrade Methods ❏ By TFTP command (for Windows XP/2000/NT4.0) For more information, ask your dealer. Rev. A Specifications 5-9

Section	Page
UB-E02 Technical Reference Guide	1
10Base-T/100Base-TX	1
Ethernet Interface board	1
Revision Information	4
About This Guide	5
Contents of the Guide	5
Related Documents	5
EMC and Safety Standards Applied	6
CE Marking	6
FCC Compliance Statement For American Users	6
For Canadian Users	6
GEREÄUSCHPEGEL	7
Key to Symbols	7
Safety Precautions	8
Label	8
Product Servicing	8
Introduction	9
Operating Environments	9
Supported Operating Systems	9
Supported Protocols	9
Environments for Setup Utility	9
Supported TM Printers	10
How to Use this Guide	11
Installation Overview	11
Programming	11
Appendix	11
Contents	12
Chapter 1	15
System Preparation	15
1.1 Supported Operating Systems	15
1.2 Supported Network Protocols	15
1.3 Supported TM Printers	15
1.4 Other Limitations	16
Chapter 2	17
Installation	17
2.1 Installation Precautions	17
2.2 Unpacking	18
2.3 Part Names	18
2.4 Functions	18
2.4.1 Switch	18
2.4.2 LEDs	18
2.5 UB-E02 Installation	19
2.6 Initializing UB-E02	22
2.7 UBE02 Status Sheet Printing	22
2.8 FAQ	23
2.8.1 Q1. The printer does not operate correctly. (\	23
2.8.2 Q2. The self test does not operate correctly.	23
2.8.3 Q3. Starting up the printer takes a long time.	23
Chapter 3	25
Utilities	25
3.1 Setting the IP Address	25
3.1.1 Setting the IP Address using EPSON TMNet WinConfig	25
3.1.2 Setting the IP Address Using the arp/ping Command	35
3.2 EPSON TMNet WinConfig Functions	37
3.2.1 Menu Bar	38
3.3 EPSON TMNet WebConfig Functions	44
3.3.1 Opening Screen	44
3.3.2 Protocol Information and Settings	46
Chapter 4	57
Programming Samples	57
4.1 Method of Printing to the UB-E02	58
4.1.1 Buffer of the UB-E02	58
4.2 Direct Printing by PORT9100	59
4.2.1 For Windows Console	59
4.2.2 For Linux	61
4.3 Commands Sent to a TM Printer When the Power is On	62
4.4 Monitoring of the ASB status	62
4.5 The Priorities of Printing	62
4.6 Time-out for Connection	62
4.7 Printer Operation by the UDP Commands	63
4.7.1 Commands Packets	63
4.7.2 03-0000 Retrieving Basic Information	64
4.7.3 03-0010 Retrieving Status	64
4.7.4 03-0011 Forced Transmission	65
4.7.5 03-0012 Reset	65
4.7.6 03-0013 Buffer Flash	66
4.7.7 03-0016 Clearing Connection Time-Out Timer	66
4.7.8 Programming Sample	67
Chapter 5	71
Specifications	71
5.1 Printer Connection	71
5.2 Line Display Connection	71
5.3 Features	71
5.3.1 Overview	71
5.3.2 Printing Functions	72
5.3.3 Functions to Monitor Settings	72
5.3.4 Maintenance Functions	72
5.4 Hardware Specifications	72
5.4.1 Physical communications standard	72
5.4.2 Board size	72
5.4.3 External appearance and connector locations	73
5.5 Software Specifications	73
5.5.1 Basic Communications Protocols	73
5.5.2 Printing Communications Protocols	73
5.5.3 Status Inquiry and Setting Protocols	74
5.5.4 Automatic IP Address Assignment Protocols	75
5.5.5 Internal Settings	77
5.5.6 Initializing	79
5.5.7 Version Upgrading	79
5.6 Environmental Specifications	80
5.7 Storage Conditions	80
5.8 EMC and Safety Standards Applied	80
Appendix A	81
Definitions	81
A	81
D	81
E	81
I	81
M	81
N	81
P	81
S	81
T	81