Epson Expression 1680 Special Edition User Manual (w/EPSON TWAIN software) - Page 27

Installing the Macintosh Software, the Windows Software

Get Epson Expression 1680 Special Edition PDF manuals and user guides View all Epson Expression 1680 Special Edition manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

2. Squeeze the lock releases on the lock connector end of your SCSI cable, and then plug the cable into either SCSI connector on the back of the scanner. The cable is secure when both connector locks snap in. 3. Connect the pin end of the SCSI cable to the SCSI port on your computer, or to another SCSI device in the chain. Tighten the screws to secure the cable. If you are connecting the scanner directly to your computer, use a cable no more than 9.8 feet (3 meters) long. Don't use an external terminator. 4. Locate the SCSI terminator switch at the rear of the scanner. If the scanner is your only SCSI device, or if it's the last device in a SCSI chain, leave the terminator switch turned ON. If you've connected your scanner in the middle of a SCSI chain, turn the terminator switch OFF. terminator switch Continue with the instructions in "Installing the Windows Software" on page 22 or "Installing the Macintosh Software" on page 47. 20 Setting Up Your Scanner

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
20
Setting Up Your Scanner
2.
Squeeze the lock releases on the lock
connector end of your SCSI cable, and
then plug the cable into either SCSI
connector on the back of the scanner.
The cable is secure when both connector
locks snap in.
3.
Connect the pin end of the SCSI cable
to the SCSI port on your computer, or to another SCSI device in the chain.
Tighten the screws to secure the cable.
If you are connecting the scanner directly to your computer, use a cable no
more than 9.8 feet (3 meters) long.
Don
’
t use an external terminator.
4.
Locate the SCSI terminator switch at the rear of the scanner.
If the scanner is your only SCSI device, or if it
’
s the last device in a SCSI chain,
leave the terminator switch turned
ON
.
If you
’
ve connected your scanner in the
middle of a SCSI chain, turn the
terminator switch
OFF
.
Continue with the instructions in
“
Installing
the Windows Software
”
on page 22 or
“
Installing the Macintosh Software
”
on
page 47.
terminator switch