Epson LQ-300 Product Information Guide - Page 10

of the, printer.

Get Epson LQ-300 - Impact Printer PDF manuals and user guides View all Epson LQ-300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

EPSON LQ-300 2. Release the sprocket units by pulling the sprocket locks forward. f----* 5. To separate the incoming paper from the printed paper, attach the paper guide by holding it horizontally and fitting its notches over the printer's mounting posts as shown below. Then slide the paper guide toward the front of the printer until you feel it click. 3. Slide the left sprocket unit using the scale on the printer as a guide. The printer prints to the right of the position marked 0. Rush the sprocket lock lever back to lock it in place. Then slide the right sprocket unit to match the width of your paper, but do not lock it. Move the paper support so it is midway between the sprocket units. 6. Slide the left edge guide to the center until it stops at the diamond-shaped guide mark. Then slide the right edge guide to the opposite guide mark. 4. Make sure your paper has a clean, straight leading edge. Open~sprocketcwers.Fit~firstholesof~paper over the sprocket pins and then close the sprocket covers. Slide the right sprocket unit to remove any slack in the paper and lock it in place. Now the paper is in the paper-park position. Note: a Do not use the knob tofeed pper, othemise the tqof$rm pition may be alteredfrom the next page. a M(3faekeet)soufrethyeouprrinptaepre.r supply is positioned within I meter 7. Make sure the printer cover is closed. Then turn on the printer. When the printer receives data, it begins printing automatically. 8. When you finish printing (the printer receives no data for three seconds) the printer feeds the perforation of the continuous paper to the edge of the printer cover so that you can tear off the last sheet. The POUW light flashes. Note: P Set the auto tear o$@ature in the Printer Setting mode to on. Otherwise, the printer does notfeed the perforation to the edge of the printer cover. P If the perjkation and the edge of the printer cmer do not match, adjust the paper position byfillowing the steps in "Adjusting the loading position," while the Pause light is flashing. /-. When you send more data, the paper automatically feeds back to the loading position EPSON LQ-300-10 10/2/94 Dot Matrix Printers

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
EPSON LQ-300
2.
Release the sprocket units by pulling the sprocket locks
forward.
3.
Slide the left sprocket unit using the scale on the printer as
a guide. The printer prints to the right of the position
marked 0. Rush the sprocket lock lever back to lock it in
place. Then slide the right sprocket unit to match the
width of your paper, but do not lock it. Move the paper
support so it is midway between the sprocket units.
4. Make sure your paper has a clean, straight leading edge.
Open~sprocketcwers.Fit~firstholesof~paper
over the sprocket pins and then close the sprocket covers.
Slide the right sprocket unit to remove any slack in the
paper and lock it in place. Now the paper is in the
paper-park position.
Note:
a
a
Do not use the knob
tofeed
pper,
othemise
the
tqof$rm
pition
may be
alteredfrom
the next page.
Make sure your paper supply is positioned within
I
meter
(3
feet)
of the
printer.
f----*
5.
To separate the incoming paper from the printed paper,
attach the paper guide by holding it horizontally and
fitting its notches over the printer’s mounting posts as
shown below. Then slide the paper guide toward the front
of the printer until you feel it click.
6.
Slide the left edge guide to the center until it stops at the
diamond-shaped guide mark. Then slide the right edge
guide to the opposite guide mark.
7.
8.
Make sure the printer cover is closed. Then
turn
on the
printer. When the printer receives data, it begins printing
automatically.
When you finish printing (the printer receives no data for
three seconds) the printer feeds
the
perforation of the
continuous paper to the edge of the printer cover so that
you can tear off the last sheet. The
POUW
light
flashes.
Note:
P
Set the auto tear
o$@ature
in the Printer Setting mode to on.
Otherwise, the printer does
notfeed
the
perforation
to
the
edge
of the printer cover.
P
If
the
perjkation
and the edge of the printer
cmer
do
not match,
adjust the paper
position
byfillowing
the
steps
in “Adjusting
the loading position,” while the Pause light is flashing.
/-.
When you send more data, the paper automatically feeds
back to the loading position
EPSON LQ-300-10
10/2/94
Dot Matrix Printers