Epson SureColor S70675 Setup Guide - Page 26

of the printer turn the silver adjustment screw. Turn the screw counterclockwise to move the line

Get Epson SureColor S70675 PDF manuals and user guides View all Epson SureColor S70675 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

24 | Adjusting the Take-in Reel 13. Lift up the alignment tool and slide it to the other side of the printer, next to the right adjustment guide. Line up the alignment tool and the adjustment guide at the front and back of the printer. Note the location where the alignment tool crosses the front of the white line on the platen. If the location is different from the left side, go to step 14. If they are the same, go to step 15. 14. Make sure all four of the mounting screws are loose. To make adjustments, have a person at the back of the printer turn the silver adjustment screw. Turn the screw counterclockwise to move the line back, and turn it clockwise to move the line forward. The line will move approximately 1 mm with each turn of the screw. Continue to turn the silver adjustment screw until the measurements are the same.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
24
|
Adjusting the Take-in Reel
13.
Lift up the alignment tool and slide it to the other side of the printer, next to the right adjustment
guide. Line up the alignment tool and the adjustment guide at the front and back of the printer.
Note the location where the alignment tool crosses the front of the white line on the platen. If the
location is different from the left side, go to step 14. If they are the same, go to step 15.
14.
Make sure all four of the mounting screws are loose. To make adjustments, have a person at the back
of the printer turn the silver adjustment screw. Turn the screw counterclockwise to move the line
back, and turn it clockwise to move the line forward. The line will move approximately 1 mm with
each turn of the screw. Continue to turn the silver adjustment screw until the measurements are the
same.