Foscam FI8918W QUICK INSTALLATION GUIDE - Page 10

How do you assign a new HTTP port and a Static Local IP Address?, Click on Network Configuration - default password

Get Foscam FI8918W PDF manuals and user guides View all Foscam FI8918W manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Foscam Digital Technologies LLC FI8918W Quick Installation Guide http://192.168.1.103:80, with a colon and 80 at the end, it will default back to http://192.168.1.103. This is because it is understood that any time you are entering an IP address without a colon and port number at the end, it is defaulting to port 80 no matter what, so the colon and port 80 are taken out of the end of the link because of this. It is recommended to change port 80 to a different port, usually in the 4 digit range. The reason for this is because some other devices, such as your router, also share port 80. If this is the case you may experience slow speeds on the camera, or you may not even be able to connect at all. It is best to assign a specific port to your camera so that only your camera is using that specified port number. We usually suggest changing your port to 8080, 8090, or any type of 4 digit number, just as long as it is not at port 80. You can set the port anywhere between 1000 and 20000. How do you assign a new HTTP port and a Static Local IP Address? Open the IP Camera Tool, and select the camera you would like to change the port for. Right click on the IP address, and click on "Network Configuration", this brings up the network configuration box as shown: Select which camera you'd like to change the port for, and right click. Click on "Network Configuration" Modify the HTTP Port to a four digit number other than 80. Enter the Username and Password, and then click OK. Changing the port in IP Camera Tool -9-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
Foscam Digital Technologies LLC
FI8918W Quick Installation Guide
-9-
, with a colon and 80 at the end, it will default back to
.
This is because it is understood that any time you are entering an IP address without a colon and
port number at the end, it is defaulting to port 80 no matter what, so the colon and port 80 are taken
out of the end of the link because of this.
It is recommended to change port 80 to a different port, usually in the 4 digit range. The reason for
this is because some other devices, such as your router, also share port 80. If this is the case you
may experience slow speeds on the camera, or you may not even be able to connect at all. It is best
to assign a specific port to your camera so that only your camera is using that specified port number.
We usually suggest changing your port to 8080, 8090, or any type of 4 digit number, just as long as
it is not at port 80. You can set the port anywhere between 1000 and 20000.
How do you assign a new HTTP port and a Static Local IP Address?
Open the IP Camera Tool, and select the camera you would like to change the port for. Right click
on the IP address, and click on “Network Configuration”, this brings up the network configuration
box as shown:
Click on “Network Configuration”
Changing the port in IP Camera Tool
Select which camera
you’d like to change the
port for, and right click.
Modify the HTTP Port
to a four digit number
other than 80.
Enter the Username
and Password, and
then click OK.